Bedienungsanleitung La Nordica Sovrana Easy (Seite 25 von 84) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

696260

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

ENGLISH

CONNECTION TO THE CHIMNEY

Products with automatic door closing (type 1) must operate, for safety reasons, with the furnace door closed (except during the fuel loading

or ash removal phases).

Products with non-automatic door closing (type 2) must be connected to their own ue.

Operation with doors open is only allowed when supervised.

The connection pipe to the ue must be as short as possible, straight horizontal and positioned slightly in ascent, and watertight.

Connection must be carried out with stable and robust pipes,comply with all current Standards and Regulations and to those envisioned by

the law, and be hermetically secured to the ue. The internal diameter of the connection pipe must correspond to the external diameter of

the appliance ue gas exhaust stub pipe (DIN 1298).

ATTENTION: as far as concern the realisation of the ue connection and ammable materials please follow the requirements

provided by UNI 10683 standard. The ue must be properly spaced from any ammable materials or fuels through a proper

insulation or an air cavity. Minimum distance safety 25 cm.



IMPORTANT: the unused ue gas exhaust hole must be covered with its respective cap (See chapter: DIMENSIONS).

The chimney pressure (DRAUGHT) must be at least (see chap. TECHNICAL DATA SHEET) Pascal. The measurement has always to be carried

out with hot device (rated thermal performance).

When the depression exceeds 17 20 Pa (=1.7 =2 mm of column of water), it is necessary to reduce the same by installing an additional draught

regulator (buttery valve) on the exhaust pipe or in the chimney, according to the regulations in force.



For correct appliance operation, it is essential that sucient air for combustion is introduced into the place of installation (see

paragraph VENTILATION AND AERATION OF THE INSTALLATION PREMISES).

CONNECTING A FIREPLACE OR OPEN HEARTH TO THE FLUE

The ue gas channel is the stretch of piping which connects the product to the ue. In the connection, these simple but extremely important

principles must be respected:

• under no circumstances use a ue gas channel with a diameter less than that of the exhaust clamp with which the product is equipped;

• each metre of the horizontal stretch of the ue gas channel causes a slight loss of head which must be compensated if necessary by

elevating the ue;

• the horizontal stretch must never exceed 2 metres (UNI 10683);

• each bend of the ue gas channel slightly reduces the ue draught which must be compensated if necessary by elevating it suitably;

• The UNI 10683 – ITALY regulation requires that under no circumstances must there be more than 2 bends or variations in direction

including the intake into the ue.

If the user wishes to use the ue as a replace or open hearth, it is necessary to seal the hood below the entrance point of the ue gas channel

pos. A Picture 5.

If the ue is then too big (e.g. 30x40cm or 40x50cm), it is necessary to intubate it with a stainless steel tube with a diameter of at least 200mm,

pos. B, taking care to close the remaining spaces between the pipe and the ue immediately under the chimney pot pos. C.

CHIMNEY POT

The ue draught depends on the suitability of the chimney pot.

It is therefore essential that, if built in a handcrafted way, the exit section is more than twice the internal section of the flue (Picture 2) .

As it must always go past the ridge of the roof, the chimney pot must ensure exhaust even in the presence of wind (Picture 3).

The chimney pot must meet the following requirements:

• Have an internal section equivalent to that of the chimney.

• Have a useful exit section of double the internal section of the ue.

• Be built so as to prevent rain, snow or any foreign body entering the ue.

• Be easy to inspect, for any maintenance and cleaning operations.

VENTILATION AND AERATION OF THE INSTALLATION PREMISES

As the product draw their combustion air from the place of installation, it is MANDATORY that in the place itself, a sucient quantity of air is

introduced. If windows and doors are airtight (e.g. built according to energy saving criteria), it is possible that the fresh air intake is no longer

guaranteed and this jeopardises the draught of the appliance and your health and safety.

There MANDATORY be sucient quantity of air for combustion and re-oxygenation of the room to ensure the device will work properly.

There should therefore be vents letting air in from outside the building and enabling circulation of air for combustion even when the doors

and windows are closed.

The air inlets must meet the following requirements:

• they must be protected with grids, metal mesh, etc., but without reducing the net useful section;

• they must be made so as to make the maintenance operations possible;

• positioned so that they cannot be obstructed;

• Any extractor hoods in the room where the device is installed must not operate at the same time as this could cause smoke to enter the

room, even with the replace’s door closed.

La Nordica Sovrana Easy Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von La Nordica Sovrana Easy

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info