Bedienungsanleitung La Nordica Termocamino WF25 DSA (Seite 30 von 104) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

696296

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

ENGLISH

6. Once the «break-in» has been completed, it is possible to use the product as the motor of a car, avoiding abrupt heating with excessive

loads.



After testing the proper working of the appliance, some days from the installation, it is possible to proceed with the

construction of its aesthetic covering.

WARNING: During the surround building operations it must kept in mind possible and subsequent electrical installed parts

maintenance (Fans, temperature probe, etc) and with hydraulic systems all parts connected to the thermo-replace.

LOW EMISSION FIRE LIGHTING

Smokeless combustion is a way of lighting a re able to signicantly reduce the emission of harmful substances. The wood burns gradually

from the top downwards, so combustion is slower and more controlled. Burnt gases pass through the high temperatures of the ame and

therefore burn almost completely.

Place the logs in the hearth a certain distance apart as shown in the Picture 15. Arrange the largest at the bottom and the smallest at the

top, or vertically in the case of tall narrow combustion chambers. Place the re starter module on top of the pile, arranging the rst logs in the

module at right angles to the pile of wood.

Fire STARTER MODULE. This re starter module replaces a paper or cardboard starter. Prepare four logs, 20 cm long with a cross section of 3

cm by 3 cm Picture 15. Cross the four logs and place them on top of the pile of wood at right angles, with the re lighter (wax impregnated

wood bre for example) in the middle. The re can be lit with a match. If you want, you can use thinner pieces of wood. In this case, you will

need a larger quantity. Keep the ue gas exhaust valve and combustion air regulator open.

After lighting the re, leave the combustion air regulator open in the position shown in the Picture.

IMPORTANT:

• do not add further wood between one complete load and the next;

• do not suocate the re by closing the air intakes;

• regular cleaning by a chimney sweep reduces ne particle emissions.

These instructions are backed by ENERGIA Legno SVIZZERA www.energia-legno.ch

NORMAL OPERATION

After having positioned the registers correctly, insert the indicated hourly wood load avoiding overloads that cause anomalous stresses and

deformations.

You should always use the product with the door closed in order to avoid damages due to overheating (forge eect). The

inobservance of this rule makes the warranty expire.

IMPORTANT: For safety reasons the door of the hearth can be opened only for the loading of the fuel. The hearth door must

always remain closed during operation or rest.

With the registers located on the front of the device, it is possible to adjust the heat emission of the same. They have to be opened according to

the caloric need. The best combustion (with minimum emissions) is reached when, by loading the wood, most part of the air for combustion

ows through the secondary air register.

Never overload the appliance. Too much fuel and too much air for the combustion may cause overheating and then damage the

product. You should always use the appliance with the door closed in order to avoid damages due to overheating (forge eect).

The adjustment of the registers necessary to reach the rated caloric yield is the following one: see chap. TECHNICAL DESCRIPTION. The

appliance works as an intermittent operating appliance.

In the event that the water temperature exceeds the tripping temperature of the safety devices, immediately suspend the

feeding of wood, and make sure that the water temperature and the ame decrease, eliminating the causes of the

overheating (if necessary by closing the air register). If the water system is connected in the thermo-replace, the hot water

tap can be opened to speed up the cooling of the appliance.

Besides the adjustment of the air for the combustion, the intensity of the combustion and consequently the thermal performance of the

device is inuenced by the stack. A good draught of the stack requires a stricter adjustment of air for combustion, while a poor draught

requires a more precise adjustment of air for combustion.

To verify the good combustion, check whether the smoke coming out from the stack is transparent.

If it is white, it means that the device is not properly adjusted or the wood is too wet; if instead the smoke is gray or black, it signals that the

combustion is not complete (it is necessary a greater quantity of secondary air).

WARNING: When fuel is added onto the embers in the absence of a ame, a considerable amount of fumes may develop. Should

this happen, an explosive mixture of gas and air may form, and in extreme cases an explosion may occur. For safety reasons it is

advisable to perform a new lighting procedure with the use of small strips.

ELECTRICAL POWER SUPPLY FAILURE

In the event of an unexpected electrical power supply failure during normal system operation, it will be necessary to carry out these simple

manoeuvres to prevent the water in the boiler starting to boil as a consequence of the lack of pump operation.

• Close completely the primary and secondary air registers in order to smother the ame as much as possible.

• Close the smokes register, if existing, to limit further coming of combustive air through possible cracks.

La Nordica Termocamino WF25 DSA Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info