Bedienungsanleitung La Nordica Termocamino WF25 X DSA (Seite 29 von 104) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

696295

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

ENGLISH

Variety kg/mc kWh/kg moistness 20%

Poplar

470 4,1

Larch*

660 4,4

Spruce*

450 4,5

Scots pine *

550 4,4

* RESINOUS WOOD NOT SUITABLE FOR THE BURNING

ATTENTION : the continuous and protracted use of aromatic wood (eucalyptus, myrtle etc.) quickly damages the

cast iron parts (cleavage) of the product.

The declared technical data have been achieved by burning beech wood class “A1” according to the requirement UNI EN ISO 17225-5 and wood

moisture content less than 20%. By burning a dierent kind of wood the eciency of the product itself could change and some specic adjustments

on the appliance could be needed.

LIGHTING

ATTENTION: never light for any reason if the installation is not completely full of water in order to avoid a serious damage

of the whole structure. IABSOLUTELY DO NOT LIGHT THE FIRE IN THE THERMO-FIREPLACE IN THE TOTAL OR PARTIAL

ABSENCE OF WATER (NOT EVEN FOR CHECKING), AS IT COULD BE IRREMEDIABLY RUINED. IN SUCH CASE THE WARRANTY ON THE

APPLIANCE IS VOIDED.

Before installing the facing and lighting the thermo-replace, it must be loaded and the system lled from the open expansion tank by means

of the natural fall of the water (see chapter. SYSTEM CONNECTION AND FILLING).

After ensuring that at least one radiator is always open, open the door and load a small quantity of wood.

To light the re, it is suggested to use small wood pieces together with paper or other traded lighting means.

It is FORBIDDEN to use any liquid substance as for ex. alcohol, gasoline, oil and similar. Never switch on the device when

there are combustible gases in the room.

The openings for air (primary and secondary) must be opened together (you must open the eventual Ignition control, and buttery valve

placed on the pipe of smokes exhaust). When the wood starts burning, you may load other fuels and adjust the air for combustion according

to the instructions on paragraph TECHNICAL DESCRIPTION.

Please always be present during this phase. Never overload the appliance (see cap. TECHNICAL DESCRIPTION - Hourly

consumption). Too much fuel and too much air for combustion can cause overheating and therefore damage the same.

After the rst ignition you can smell bad odours (owing to the drying of the glue used in the garnitures or of the paint) which

disappear after a brief using of the appliance. A good ventilation of the room should always be guaranteed.

ATTENTION: during the rst lightings there could be a solid smokes condensation with a small escape of water from the

thermo-replace: this event will expire in a very short time but if it persists it will be necessary to check the chimney

draught.

To perform a correct rst lighting of the products treated with paints for high temperature, it is necessary to know the following information:

• the construction materials of the involved products are not homogeneous, in fact there are simultaneously parts in cast iron, steel,

refractory material and majolica;

• the temperature to which the body of the product is subject is not homogeneous: from area to area, variable temperatures within the

range of 300°C - 500°C are detected;

• during its life, the product is subject to alternated lighting and extinguishing cycles in the same day, as well as to cycles of intense use or

of absolute standstill when season changes;

• the new appliance, before being considered seasoned has to be subject to many start cycles to allow all materials and paints to complete

the various elastic stresses;

• in detail, initially it is possible to remark the emission of smells typical of metals subject to great thermal stress, as well as of wet paint. This

paint, although during the manufacture it is backed at 250 °C for some hours, must exceed many times and for a given period of time the

temperature of 350 °C before becoming completely embedded in the metallic surfaces.

Therefore, it is extremely relevant to take these easy steps during the lighting:

1. Make sure that a strong air change is assured in the room where the appliance is installed.

2. During the rst starts, do not load excessively the combustion chamber (about half the quantity indicated in the instructions manual) and

keep the product continuously ON for at least 6-10 hours with the registers less open than the value indicated in the instructions manual.

3. Repeat this operation for at least 4-5 or more times, according to your possibilities.

4. Then load more and more fuel (following in any case the provisions contained in the installation booklet concerning maximum load) and,

if possible, keep the lighting periods long avoiding, at least in this initial phase, short ON/OFF cycles.

5. During the rst starts, no object should be leaned on the appliance and in detail on enamelled surfaces. Enamelled surfaces must not be

touched during heating.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

La Nordica Termocamino WF25 X DSA Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info