Bedienungsanleitung La Nordica Wanda Classic Evo (Seite 24 von 96) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

696218

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

ENGLISH

The device is equipped with registers of primary and secondary air.

A- PRIMARY air register (Picture 6)

With the primary air control is adjusted the passage of air through the ash drawer and the grate in the fuel direction. The primary air is

necessary for the combustion process. The ash drawer must be regularly emptied, so that the ash does not obstruct the primary air entry.

Through the primary air the re is also kept alive.

During wood combustion, the register of primary air must be opened only for a while, because otherwise the wood burns fast and the stove

may overheat. For the correct arrangement (see chapter Normal operation).

B - SECONDARY air register (Picture 6)

Over the door of the hearth there is the secondary air control.This regulator must be open (the lever must be moved to the right), especially

for wood combustion, so that un-burnt carbon does not undergo a post-combustion. See chapter Normal operation. Through this register

it is possible to adjust the power of the stove.

Leaving it slightly open, according to the ue of the chimney, it is possible to keep the glass clean.

The adjustment of the registers necessary to reach the rated caloric yield is the following one:

Hourly consumption in kg/h PRIMARY air SECONDARY air TERTIARY AIR

WANDA EVO 2,3 10% Open 75% Open PRE - ADJUSTED

WANDA CLASSIC EVO 2,3 10% Open 75% Open PRE - ADJUSTED

C - AIR REGISTER for the heating of the environment (Picture 6).

This register, through a fan controlled by a thermoregulator pos. D, adjusts the warm air output ONLY from the front side of the appliance.

D - FAN ELECTRIC THERMOCONTROLLER (Picture 6 - Picture 9).

UNIT OPERATION.

This electronic thermocontroller for packaged units manages ventilation air ows. The unit is switched on or o by pressing and holding the

1 button. During operation the display shows the set speed alternating with unit status, led 9.

When the unit is o, the display also remains o. The unit can be controlled MANUALLY or AUTOMATICALLY.



WARNING: the correct operation of the unit is assured only for the proper motor for which it has been manufactured.

Improper use relieves the manufacturer from each responsibility.

MANUAL mode

To access MANUAL mode, press the 2 button; when the 3 light comes on the function

is active. The 4-5 buttons are used to select one of the ve fan speeds, also active

when the ue is cold.

The motor is started in automatic mode by a mechanical thermostat (the display

shows WAIT), which is activated when the temperature is at least 45°C (xed value,

not modiable). The 6 led indicates that the thermostat contact is closed.

AUTOMATIC mode

To access AUTOMATIC mode, press the 2 button; when the 7 light comes on the

function is active. Use the 5 button to set the speed. The 4-5 buttons are used to

select one of the ve fan speeds.

In automatic mode the COMFORT temperature can also be selected. Press the 4

button to access the COMFORT temperature setting and then set the value using

4-5. This setting allows the user to reduce fan noise when the room temperature measured by the probe inside the controller exceeds the

comfort set point; the motor operates one speed lower (this mode has no eect in rst speed) and is signalled by the 8 led.

LANGUAGE menu.

Pressing and holding the 2 button accesses the LANGUAGE menu, where the display language can be changed using the 4-5 buttons (IT,

EN, DE, FR). Pressing the 2 button briey again accesses the DISPLAY menu, where the brightness can be adjusted (between 10 and 150).

Pressing the 2 button briey another time accesses the DEGREES menu, where the temperature display can be set as °C or °F.

BUZZER menu

Pressing the 2 button briey a nal time accesses the buzzer menu, where audible buzzer can be enabled or disabled.

REMOTE CONTROL OPERATION:

The electronic controller for packaged units can be managed by an IR remote control.

• The controller is switched on or o by pressing and holding the 11-12 buttons.

• To switch from MANUAL to AUTOMATIC on the IR remote control press the 13-14 buttons. The LED corresponding

to the operating mode comes on, manual 3 or automatic 7.

• In MANUAL mode only the buttons in the 11-13 group are enabled for selecting one of the ve speeds.

• In AUTOMATIC mode, the buttons in the 12-14 group are enabled for selecting one of the ve speeds, as well

as the buttons in the 11-13 group for changing the COMFORT set point.

The 10 LED comes on whenever a button is pressed on the remote control; if this does not happen, check the

batteries.

13 14

1 2 3 4

3 7 89

4 5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

La Nordica Wanda Classic Evo Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info