Bedienungsanleitung La Nordica Wanda Evo (Seite 26 von 96) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

696217

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

ENGLISH

• the horizontal stretch must never exceed 2 metres (UNI 10683);

• each bend of the ue gas channel slightly reduces the ue draught which must be compensated if necessary by elevating it suitably;

• The UNI 10683 – ITALY regulation requires that under no circumstances must there be more than 2 bends or variations in direction

including the intake into the ue.

If the user wishes to use the ue as a replace or open hearth, it is necessary to seal the hood below the entrance point of the ue gas channel

pos. A Picture 5.

If the ue is then too big (e.g. 30x40cm or 40x50cm), it is necessary to intubate it with a stainless steel tube with a diameter of at least 200mm,

pos. B, taking care to close the remaining spaces between the pipe and the ue immediately under the chimney pot pos. C.

VENTILATION AND AERATION OF THE INSTALLATION PREMISES

As the product draw their combustion air from the place of installation, it is MANDATORY that in the place itself, a sucient quantity of air is

introduced. If windows and doors are airtight (e.g. built according to energy saving criteria), it is possible that the fresh air intake is no longer

guaranteed and this jeopardises the draught of the appliance and your health and safety.

IMPORTANT: For a better comfort and corresponding oxygenation of environment, the combustion air can be directly withdrawn at the

outside through a junction which is to be connected with a exible pipe. The connection pipe (not furnished) must be at with a minimum

diameter of Picture 6 a maximum length of 3 m and with no more than 3 bends. If there is a direct connection with the outside it must be

endowed with a special windbreak.

There MANDATORY be sucient quantity of air for combustion and re-oxygenation of the room to ensure the device will work properly.

There should therefore be vents letting air in from outside the building and enabling circulation of air for combustion even when the doors

and windows are closed.

The air inlets must meet the following requirements:

• they must be protected with grids, metal mesh, etc., but without reducing the net useful section;

• they must be made so as to make the maintenance operations possible;

• positioned so that they cannot be obstructed;

• Any extractor hoods in the room where the device is installed must not operate at the same time as this could cause smoke to enter the

room, even with the replace’s door closed.

The clean and non-contaminated air ow can also be obtained from a room adjacent to that of installation (indirect aeration and ventilation),

as long as the ow takes place freely through permanent openings communicating with the outside.

The adjacent room cannot be used as a garage, or to store combustible material or for any other activity with a re hazard, bathroom, bedroom

or common room of the building.

Ventilation is deemed sucient when the room is equipped with air inlets according to the table:

Appliance categories Reference standard

Percentage of the

net opening section with respect to

the appliance fumes outlet section

Minimum net opening value of

the ventilation duct

Fireplaces UNI EN 13229 50% 200 cm²

Stoves UNI EN 13240 50% 100 cm²

Cookers UNI EN 12815 50% 100 cm²

Installation in premises with re hazards is forbidden. Installation in residential premises in which, in any case, the depression

measured during installation between the internal and external environment is greater than 4 Pa - reference for Italy according to

standard UNI10683.

All national, regional, provincial and municipal laws and standards in force in the country where the appliance is installed must be complied

with.

CANALIZATION OF THE WARM AIR

The heat distribution will take place through the ventilation of the installation environment, or of the adjacent room by the connection in the

back of heat resistant ventilation pipes.

Therefore, during installation, it is necessary to establish the type of ventilation or convection to be adopted (A - B see chapter INSTALLATION).

Conguration A - Ventilation output ONLY from the front side of the appliance:

a) Warm air output ONLY from the front side of the appliance: do NOT remove the semi-blanks.

b) Adjust through the register C - Picture 6 the warm air output only from the front side of the appliance.

Conguration B - Ventilation and CANALIZATION:

a) Warm air output from the front and rear side of the appliance: REMOVE the semi-blanks.

b) Perform the drilling on the walls to allow the passage and the application of the (re-resistant) hoses equipped with related openings.

c) Fasten the pipes by means of clamps to the related collars and openings.

d) Each pipe must not exceed 4 m for forced ventilation, and has to be insulated with insulating materials to avoid noise and loss of heat.

e) The openings have to be positioned at a height not lower than 2 m from the oor to avoid that hot air at output meets people; Please

respect the distance of the convection openings according to the local construction norms.

f) The lengths of the canalization pipes must have the same length to avoid the distribution of diering quantities of air from each

output.

La Nordica Wanda Evo Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info