Bedienungsanleitung Lamax Shield Plus (Seite 18 von 132) (Deutsch, Englisch, Polnisch)

699083

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

Installation Tips

Installing the Magnetic Sensor

The magnetic sensor can be installed on windows, doors or any other object that can be opened or

closed. The sensor consists of two parts, the larger sensor part and the smaller magnet part. The sensor

attaches to the frame and the magnet to the moving part.

When installed correctly, the LED on the magnetic sensor blinks once when the two parts are separa-

ted by more than a centimetre. When closed, the spacing between the two parts must not be more

than one centimetre.

Both parts of the magnetic sensor attach with double sided tape or screws.

Do not install the magnetic sensor on metal surfaces or in places where there are a large number of

metal parts. Ensure the LED blinks when the window or doors opens.

IMPORTANT: On both parts of the magnetic sensor there is an arrow. Parts must be xed with the

arrow pointing towards you.

Connecting the Magnetic Sensor

1. Ensure the sensor is mounted next to the magnet at a distance of less than one centimetre.

2. Enter the passcode into the control panel and press “RECORD”.

3. Record button lights up.

4. Separate the two parts of the sensor from each other at a distance of greater than one centimetre.

5. The sensors will record the event. When the sensor is successfully paired, the control panel will beep.

If the control panel beeps twice, it means the sensor has already been paired.

Electric Lock Output

The PUSH and GND connector of the electric lock can be connected to the PUSH and GND at the rear

of the control panel.

Once the security system is connected to the electric lock and disarmed, the control panel sends a

signal to the lock and unlocks it.

NOTE: Doors equipped with an electric lock automatically unlock when there is a power failure. We strongly

recommend connecting a backup power device.

Installing the Control Panel

The control panel can be mounted directly on the wall or using the stand on any at surface.

Installing on the Wall

The control panel can be mounted on the wall using the bracket and screws included. Insert the con-

trol panel into the bracket from top to bottom. The bracket ensures that the tamper switch is conti-

nually depressed.

Installing on a Flat Surface

Using the stand, the control panel can be installed on any at surface. Insert the control panel into the

stand from top to bottom. The stand ensures that the tamper switch is continually depressed.

IMPORTANT: Pressing the tamper switch several times resets the system.

Assigning Sensors to Modes

Each sensor can be assigned to one of four dierent modes. The security system recognizes home

mode, normal mode, 24-hour mode and single zone mode.

IMPORTANT: Before you set the security system, decide which sensor to put in which group. If you

want to change which group the sensor is in, the sensor must be disconnected from the control

panel.

The gure below shows the sensor switch setting for each group.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lamax Shield Plus Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info