Bedienungsanleitung Lancom 730-4G plus (Seite 1 von 1) (Englisch)

703332

Zoom out

Zoom in

Vorherige Seite

1/1

Nächste Seite

LANCOM, LANCOM Systems and LCOS are registered trademarks. All other names or descriptions used may be trademarks or registered

trademarks of their owners. Subject to change without notice. No liability for technical errors and/or omissions. 111785/0119

Hardware

Power supply 12 V DC, external power adapter 230 V with bayonet connector to secure against

disconnection

Power consumption Approx. 12 W via external 12 V / 2,0 A power adapter (value refers to the overall power for the

router and power adapter);

approx. 11 W via PoE (value refers solely to the power of the device)

Environment Temperature range 0° to +40°C a vertical mounting position using the LANCOM Wall Mount;

Temperature range 0° to 35°C a horizontal mounting position and adequate ventilation;

humidity up to 95%; non-condensing; In order to prevent overheating of the device the LTE

module is deactivated automatically.

Housing Robust synthetic housing, rear connectors, ready for wall mounting,Kensington lock;

measures 210 x 45 x 140 mm (W x H x D)

Number of fans None; fanless design, no rotating parts, high MTBF

Interfaces

WAN, LAN 10 / 100 / 1000 Base-TX, autosensing, auto node hub

Serial interface Serial conguration interface / COM port (8-pin Mini-DIN): 9,600–115,000 baud, suitable

for optional connection of analog / GPRS modems. Supports internal COM-port server and

provides transparent asynchronous serial-data transfer via TCP.

4G: Ant 1, Ant 2 Two SMA connectors for the supplied dipole rod antennas (LTE, HSPA+, HSxPA, UMTS),

compatible LANCOM AirLancer antennas for 4G, or from other manufacturers**

Data transmission in cellular networks

Supported standards LTE Advanced, LTE, HSPA+, HSxPA, UMTS

LTE / HSPA+ /

HSxPA / UMTS

Band 1 (2100 MHz), band 2 (1900 MHz), band 3 (1800 MHz), band 4 (2100 MHz),

band 5 (800 MHz), band 7 (2600 MHz), band 8 (900 MHz), band 12 (700 MHz),

band 13 (700 MHz), band 20 (800 MHz), band 25 (1900 MHz), band 26 (800 MHz),

band 29 (700 MHz), band 30 (2300 MHz), band 41 (2500 MHz)

Maximum transmission

power

+23 dBm

Declaration of Conformity

Hereby, LANCOM Systems declares that this radio equipment is in compliance with Directive 2014/53/EU. The full text

of the EU declaration of conformity is available at the following internet address: www.lancom-systems.com/ce/

Package content

Manual Hardware Quick Reference (DE/EN), Installation Guide (DE/EN)

Cable 1 Ethernet cable, 3m (kiwi-colored connector)

Antenna Two LTE / 4G antennas for LTE, HSPA+, HSxPA, UMTS

Power adapter External power adapter, NEST 12 V / 2 A DC/S, barrel connector 2.1 / 5.5 mm bayonet,

LANCOM item no. 111303 (not for WW devices)

a Power

Off Device switched off

Green,

permanently*

Device operational,

resp. device paired / claimed and LANCOM

Management Cloud (LMC) accessible

Green/orange,

blinking

Conguration password not set. Without a

conguration password, the conguration

data in the device is unprotected.

1x green inverse

blinking*

Connection to the LMC active, pairing OK,

claiming error

2x green inverse

blinking*

Pairing error, resp.

LMC activation code / PSK not available

3x green inverse

blinking*

LMC not accessible, resp.

communication error

d ETH

Off No networking device attached

Green,

permanently

Connection to network device operational,

no data trafc

Green, ickering Data transmission

SETTING UP AND CONNECTING THE DEVICE

TECHNICAL DATA

b 4G

Off Cellular interface disabled

Green,

permanently

Connection to cellular network active

Green, ickering Cellular data transmission

Orange,

permanently

Logon to cellular network successful

Orange, blinking Logging on to cellular network

Red,

permanently

Hardware error/module unavailable

Red/green, blinking SIM card error (PIN)

Red/orange,

blinking

Uploading module rmware

c Signal

Off No cellular reception

Green,

permanently

Good signal strength,

greater than or equal to -70 dB

Orange,

permanently

Medium signal strength,

eld strength between -86 and -71 dB

Orange, blinking Low signal strength,

eld strength less than -87 dB

**) Please respect the restrictions which apply in your country when setting up an antenna system (in particular the

antenna gain and transmission power).

This product contains separate open-source software components which are subject to their own licenses, in particular

the General Public License (GPL). The license information for the device rmware (LCOS) is available on the device‘s

WEBcong interface under “Extras > License information“. If the respective license demands, the source les for the

corresponding software components will be made available on a download server upon request.

LANCOM 730-4G+

Signal

Power

ETH 1

LTE / 4G antennas

Connect the two supplied cellular antennas to the connectors

Ant 1 and Ant 2.

Power

After connecting the cable to the device, turn the bayonet

connector 90° clockwise until it clicks into place.

Use only the supplied power adapter.

Conguration interface

Conguring the device via the serial interface requires a serial

conguration cable (available as an accessory).

Reset button

Pressed up to 5 seconds: device restart

Pressed until rst ashing up of all LEDs:

conguration reset and device restart

Ethernet interface

Use the cable with the kiwi-colored connectors to connect the

interface ETH1 to your PC or a LAN switch.

SIM card slot

Slide the SIM card into the slot using the marker to ensure that

the card is the right way round.

Ensure that the SIM card clicks into place on insertion. To

remove the card from the device again, press the card lightly

into the device. Let go to release the SIM card from the slot.

SIM

b c d a

DC 12 V

4G Ant 2

Config (Com) Reset

LAN

ETH 1 PoE

SIM

4G Ant 1

a e f

Please observe the following when setting up the device

A Do not rest any objects on top of the device

A For devices to be operated on the desktop, please attach the

adhesive rubber footpads

A In case of wall mounting, use the drilling template as supplied

A Keep the ventilation slots on the side of the device clear

of obstruction

A Rack installation with the optional LANCOM Rack Mount

(separately available)

When working with separately purchased antennas, please ensure you do not exceed the maximum permissible trans-

mission power. The system operator is responsible for adhering to the threshold values.

Antennas are only to be attached or changed when the device is switched off. Mounting or demounting antennas with

the device switched on may cause the destruction of the 4G modules!

The SIM card is only to be inserted or removed when the device is switched off. Inserting or

removing the SIM card with the device switched on may cause the destruction of the 4G module!

*) The additional power LED statuses are displayed in 5-seconds

rotation if the device is congured to be managed by the LANCOM

Management Cloud.

Cloud-ready

a cb d

LANCOM 730-4G+

Quick Reference Guide

Lancom 730-4G plus Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Lancom 730-4G plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info