Bedienungsanleitung Lancom R883VAW (Seite 1 von 1) (Englisch)

680887

Zoom out

Zoom in

Vorherige Seite

1/1

Nächste Seite

MOUNTING AND CONNECTING THE DEVICE

TECHNICAL DETAILS

LANCOM, LANCOM Systems and LCOS are registered trademarks. All other names or descriptions used may be trademarks or registered

trademarks of their owners. Subject to change without notice. No liability for technical errors and/or omissions. 111641/0418

Hardware

Power supply 12 V DC, external power adapter (230 V); bayonet connector to secure against disconnection

Power consumption Max. ca. 14 W

Environment Temperature range 0–35 °C; humidity 0–95 %; non-condensing

Housing Robust synthetic housing, rear connectors, ready for wall mounting, Kensington lock; measures

210 x 45 x 140 mm (W x H x D)

Number of fans None; fanless design, no rotating parts, high MTBF

Interfaces LANCOM R883VAW over ISDN

WAN: VDSL2 a VDSL2 as per ITU G.993.2; proles 8a, 8b, 8c, 8d, 12a, 12b, 17a;

a Compatible to VDSL2 from Deutsche Telekom

a ADSL conformity according to: ADSL2+ over ISDN as per ITU G.992.5 Annex B/J with DPBO,

ADSL2 over ISDN as per ITU G.992.3 Annex B, ADSL over ISDN as per ITU G.992.1 Annex B.

a Supports just one virtual connection at a time in ATM (VPI-VCI pair)

Wi-Fi a Frequency band: 2400-2483.5 MHz (ISM) or 5150-5825 MHz (restrictions vary between

countries)

a Radio channels 2.4 GHz: Up to 13 channels, max. 3 non-overlapping (2.4-GHz band)

a Radio channels 5 GHz: Up to 26 non-overlapping channels (channels available vary

according to country regulations; DFS for automatic dynamic channel selection required)

ETH 4 individual ports, 10 / 100 / 1000 Mbps Gigabit Ethernet, by default set to switch mode.

Up to 3 ports can be operated as additional WAN ports. Ethernet ports can be electrically

disabled in the LCOS conguration.

USB USB 2.0 hi-speed host port for connecting USB printers (USB print server),

serial devices (COM-port server) or USB drives (FAT le system)

ISDN 1 / ISDN 2 ISDN 1: Internal (NT) or external (TE) ISDN bus. This feature is controlled by LCOS. According to

the settings, connect the light-blue ISDN cable either to the NTBA or the ISDN terminal device.

ISDN 2: Internal (NT) ISDN bus. Use the light-blue ISDN cable to connect the ISDN device to

the ISDN interface.

Analog 1 / Analog 2 Use the cable of your analog devices to connect them with the analog interfaces. If necessary,

use the enclosed adapter.

Cong (Com) / V.24 Serial conguration interface/COM-port (8-pin mini-DIN): 9,600 - 115,200 baud, suitable for

optional connection of analog/GPRS modems. Supports internal COM-port server and provides

transparent asynchronous serial-data transfer via TCP.

WAN protocols

VDSL, ADSL, Ethernet PPPoE, PPPoA, IPoA, Multi-PPPoE, ML-PPP, PPTP (PAC or PNS) and IPoE (with or without

DHCP), RIP-1, RIP-2, VLAN

ISDN DSS1 (Euro-ISDN), PPP, X75, HDLC, ML-PPP, V.110/GSM/HSCSD

Declaration of Conformity

Hereby, LANCOM Systems declares that this radio equipment is in compliance with Directive 2014/53/EU. The full text

of the EU declaration of conformity is available at the following internet address: www.lancom-systems.com/ce/

Package content

Manual Quick Reference Guide (DE/EN); Installation Guide (DE/EN)

Cable 1 Ethernet cable, 3m (kiwi colored connectors); 1 DSL cable for an IP-based line, 4.25m;

1 ISDN cable, 3m (light-blue connectors)

Adapters 2 TAE adapters (RJ11 - TAE)

Power adapter External power supply adapter (230 V); NEST 12 V / 1.5 A DC/S; barrel connector 2.1 / 5.5 mm

bayonet; LANCOM item no. 111301

This product contains separate open-source software components which are subject to their own licenses, in particular

the General Public License (GPL). The license information for the device rmware (LCOS) is available on the device‘s

WEBcong interface under “Extras > License information“. If the respective license demands, the source les for the

corresponding software components will be made available on a download server upon request.

i VPN

Off VPN connection inactive

Green, permanently VPN connection active

Green, ashing VPN connecting

e ISDN

Off Interface deactivated

Green, permanently D-channel active

Green, ickering ISDN data transfer

Red, ickering ISDN transfer error

Red/orange, blinking ISDN hardware error

b Online

Off WAN connection inactive

Green, permanently WAN connection active

Red, permanently WAN connection error

c DSL

Off Interface deactivated

Green, permanently DSL connection active

Green, ickering DSL data transfer

Red, ickering DSL transfer error

Red/orange, blinking DSL hardware error

Orange, blinking DSL training

Orange, permanently DSL sync

Green, blinking DSL connecting

d Analog

Off Interface deactivated

Green, permanently Interface activated

Orange, blinking Incoming call

Green, blinking Connection active

h VoIP

Off No SIP accounts dened or VCM is off

Green, permanently All dened and active SIP accounts

(outgoing) were successfully registered

Red, permanently Not all dened and active SIP accounts

were registered (possibly still in process)

Red or green,

inverse ashing

Number of currently used lines (connecting

or connected)

f ETH

Off No networking device attached

Green, permanently Connection to network device operational,

no data trafc

Green, ickering Data transmission

g WLAN

Off No Wi-Fi network dened or Wi-Fi module

deactivated. The Wi-Fi module is not

transmitting beacons.

Green, permanently At least one Wi-Fi network is dened and

Wi-Fi module activated. The Wi-Fi module

is transmitting beacons.

Green, blinking DFS scanning or other scan procedure

j Reset

Reset switch

Operated e.g. with a paper clip

a short press: Restart the device

a long press: Reset the device

a Power

Off Device switched off

Green, permanently* Device operational, resp. device paired /

claimed and LANCOM Management Cloud

(LMC) accessible

Red/green blinking Conguration password not set. Without a

conguration password, the conguration

data in the device is unprotected.

Red blinking Charge or time limit reached

1x green inverse

blinking*

Connection to the LMC active, pairing OK,

device not claimed

2x green inverse

blinking*

Pairing error, resp. LMC activation code

not available

3x green inverse

blinking*

LMC not accessible, resp. communication

error

LANCOM R883VAW

DSL

ETH 2

Power

ETH 1

Online

ISDN 1

ETH 4

ETH 3

VPN

Analog 1

Analog 2

ISDN 2

WLAN

Reset

VoIP

a c eb gfd ih j

LANCOM R883VAW

Quick Reference Guide

*) After a rmware upgrade to LCOS 10.14 the additional power LED

statuses are displayed in 5-seconds rotation if the device is

congured to be managed by the LANCOM Management Cloud.

Gigabit Ethernet 10/100/1000

ISDN 1 ISDN 2

TE / NT NT

VDSL

Analog 1Analog 2

a b c d e f

Please observe the following when setting up the device

A Do not rest any objects on top of the device

A For devices to be operated on the desktop, please attach the

adhesive rubber footpads

A In case of wall mounting, use the drilling template as supplied

A Keep the ventilation slots on the side of the device clear

of obstruction

A Rack installation with the optional LANCOM Rack Mount

(separately available)

LANCOM 1681V

Power

VDSL

Online

ETH 1

ETH 2

VPN

ETH 3

ETH 4

ISDN Status

VDSL interface

Use the supplied DSL cable for the IP-based line to connect the

VDSL interface and the provider’s telephone socket. For more

infor mation, please contact your Internet service provider.

Ethernet interfaces

Use the cable with the kiwi-colored connectors to connect one of

the interfaces ETH 1 to ETH 4 to your PC or a LAN switch.

Analog interfaces

Connect analog terminal devices to the analog interfaces either

directly via RJ11, or with the help of the enclosed TAE adapters.

Conguration interface

Use a serial conguration cable to connect the serial interface

(COM) to the serial interface of the device you want to use for

conguring / monitoring (separately available).

ISDN interfaces

ISDN 1:

Internal (NT) or external (TE) ISDN bus.

This feature is controlled by LCOS.

ISDN 2:

Internal (NT) ISDN bus.

A 100-Ohm resistor for line termination is

switchable in LCOS.

USB interface

You can use the USB interface to connect a USB printer or a

USB memory stick.

Power

After connecting the cable to the device, turn the bayonet

connector 90° clockwise until it clicks into place.

Use only the supplied power adapter.

Lancom R883VAW Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Lancom R883VAW

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info