Bedienungsanleitung Land Rover TestBook (Seite 27 von 99) (Englisch)

626350

Zoom out

Zoom in

Vorherige Seite

1/99

Nächste Seite

HARDWARE

INTERNAL POWER (TESTBOOK 1)

To provide brief "stopgap" power while unplugged,

TestBook has an internal nicad battery. The internal

battery is located behind the dummy panel at the

front of TestBook. It will provide between five to ten

minutes of use on a full charge. It is only meant to

provide power when moving TestBook into and out

of a vehicle before and after a road test. During the

road test itself, you must use the Road Test Power

Supply - which is described in the next section.

When using battery power, the light on the front of

TestBook will change from the green one adjacent to

the plug symbol to the amber one next to the battery

symbol. This amber light will begin to flash when the

battery power becomes low. This means that the

unit will shut off after a short period of time if you do

not plug it back into an external power supply.

NOTE: The internal nicad battery

recharges whenever TestBook is plugged

into an external power supply - even when

Testbook is not switched on.

NOTE: As with any nicad battery, when the

TestBook internal battery becomes

drained, a period of at least two hours

must be allowed for it to recharge. If you have

removed the power supply with TestBook

operating and the amber light has started

flashing, this indicates that the nicad battery is

nearly drained. If TestBook is connected to a

power supply for only a short period of time after

the amber light has been allowed to flash, the

battery will not have recharged sufficiently to

power TestBook for the normal 5 to 10 minute

ROAD TEST POWER SUPPLY

One of the major advantages of TestBook is that it

can be taken out in a vehicle to carry out diagnostic

work during a road test. To do this, you must use the

Road Test Power Supply. Carry out the following

steps when using the Road Test Power Supply. You

do not need to turn TestBook OFF.

1. Connect the Road Test power Supply to the

battery of the vehicle to be road tested.

Connect the red cable to the battery "+" post.

Always double check that you have connected

the red cable to the correct, positive terminal

before going on to connect the black cable to

the battery "-" post. This is very important, as

the polarity must NOT be reversed.

2. Switch off TestBook’s power supply at the

power point on the side of the trolley.

3. Unplug the power supply from TestBook.

4. Plug the other end of the Road Test Power

supply into TestBook’s power port.

5. Return TestBook to a mains power point as

soon as you finish the road test.

6. When transferring TestBook to and from the

Road Test Supply, remember the limited time

available on the internal battery - don’t let

anything else distract you while doing this !

7. Allow at least two hours to fully recharge the

internal nicad battery. The battery recharges as

long as TestBook is plugged in, even when the

unit is switched OFF.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Land Rover TestBook Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info