Bedienungsanleitung Laserliner Digi-Master 5m (Seite 1 von 1) (Englisch)

646727

Zoom out

Zoom in

Vorherige Seite

1/1

Nächste Seite

How to carry out a measurement:

· Press the Block Key and check whether

the measuring tape is completely

retracted into the housing. ·Turn on

your Digi-Master via the ON/MODE key.

The display will show the measurement

'O' and the measurement unit (m, cm,

feet, inches) of the last entry. ·As and

when necessary change the

measurement unit by using the

ON/MODE key. ·Check whether there

are still measurements present in the

memory. If this is the case the display in

the lower right corner will show the

number of stored items. ·Now carry out

the measurement as you would with a

conventional measuring tape. Hold

down the Block Key whilst the measure-

ment tape is being extended. The

display will show the length of the

extended tape during the extension

period. To achieve an exact reading stop

the tape with the Block Key. ·You can

end the measurement process by hol-

ding down the Block Key and carefully

letting the tape roll back into the hou-

sing.

How to carry out an interior

measurement:

· If, for example, you want to measure

the distance between two walls, after

turning on, just press down the +CASE

key. The Digi-Master will automatically

add on the length of the housing. ·Now

you only need to direct the measuring

tape onto the full length between the

points to be measured. · When you

press the +CASE key the standard

measurement will appear: the length of

the extended tape without the housing.

How to freeze-frame the displayed

result:

· Whilst the measuring tape is still rolled

out press the Ï/MR key. The display will

be frozen, even when you retract the

measuring tape into the housing. A

small lock symbol will appear in the

display.

· The freeze-frame function can be

removed by pressing once more on the

Ï/MR key.

How to add up various

measurement values

·If you want to memorise a displayed

measurement for further addition of

lengths, then just press the M+ key. A

small figure will be displayed in the

lower right corner of the display - this

indicates the number of measurements

already stored in the memory. ·With the

measuring tape retracted press the

Ï/MR key. The total of all stored

measurements will appear in the display.

An M will appear, as a function symbol,

before the figures showing the number

of items in the memory.

How to empty the memory:

· With the measuring tape in a retracted

position press on the MC key - the

memory will be empty again.

How to do circles and curves:

· The Digi-Master has a very practical

little device for such tasks: a folding

pivot pin under the battery

compartment.

· Now draw the measuring tape a few

centimetres out of the housing. You will

notice that there are holes stamped into

it at regular intervals. These serve as a

marking assistance. ·The first hole is the

most important for doing circles. It is to

be found at 2.5 cm. This is exactly the

amount by which the housing is

increased when the pivot pin is in an

unfolded position. ·Now switch the Digi-

Master into the ON/MODE and

immediately press +CASE. Extend the

measuring tape to the length shown in

the display. Set the pivot pin at the

point where the curve is to begin and/or

at the centre point of the circle which is

to be drawn. When describing a circle

or curve put your marking pen in the

small hole in the 2.5 cm position. Your

circle will have a radius exactly as shown

in the display.

Useful tips:

· Before use please insert a 9 volt

alkaline battery.

· If the display shows the word ERROR ,

there can be four reasons for this:

1. You may have extended the tape and

then pressed ON/MODE. Retract the

tape completely:

2. You may have pressed ON/MODE

whilst the appliance was turned off and

the tape was not completely retracted.

Retract the tape completely:

3. The memory may be overloaded with

additional measurement figures. Delete

these by pressing MC:

4. You may have retracted the tape too

quickly. Retract it once more and press

MC.

· It is difficult to read the display or the

battery symbol appears. Replace the

battery.

· Always retract the measuring tape

slowly and carefully. Whilst doing this

with one hand hold it in a stable

position. Do not let children use it: the

edges of the steel tape can cause injury.

· Keep your Digi-Master under dry

conditions and do not expose it to direct

sunlight.

· Should you not be going to use the

appliance for a considerable time then

please remove the battery in order to

avoid damage from battery leakage.

· The appliance can be used within a

temperature range of 0° - 40° C.

Operating Instructions

ENGLISH

Mayer & Wonisch GmbH & Co. KG

Donnerfeld 2 D-59757 Arnsberg

Phone: +49 2932–638 300 / Fax: +49 2932–638 333

Delivery and dispatch address:

Möhnestraße 149 D-59755 Arnsberg

LASERLINER

Innovation in tools

Laserliner

Digi-Master 5m

1. Hold down the Block Key when

pushing in or pulling out the measuring

tape.

2. IC Display

3. Lid of the battery compartment

4. ON/MODE turns the Digi-Master on

and changes the unit of measurement

(the Digi-Master automatically turns

itself off after 30 sec.)

5. +Case automatically adds on the

length of the appliance housing

6. MC deletes the memory

7. M+ adds the amount measured into

the memory

8. 5m long steel measuring tape

9. Ï/MR

a.) when the measuring tape is

extended the display goes into

freeze-frame

b.) when the measuring tape is

retracted the total amount is shown

123

678

digi_gb.qxd 07.06.01 09:30 Seite 1

Laserliner Digi-Master 5m Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Laserliner Digi-Master 5m

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info