Bedienungsanleitung Laurastar premium evolution (Seite 6 von 15) (Englisch)

321499

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

Filling

Please refer to the last two pages of the manual.

Unscrew the appropriate cap (16) and fill the boiler with water. To fill

it up use the bottle (9) provided: it has an anti-overfill device which

stops the flow when the boiler is full (the capacity of the bottle is

greater than that of the boiler).

Squeeze the bottle briefly to start the filling of the boiler. Once full,

screw the filling cap back on again (16) as far as it will go.

Fix the board in the highest

position. Put the rinsing recep-

tacle beneath the boiler.

Unscrew the drain cap (15).

Unscrew the filling cap (16).

Pass the contents of a bottle (9)

of hot water through the boiler

to rinse it. Screw the drain cap

back on again (15).

Screw the filling cap back on

again (16).

CAUTION: Fill up the boiler

before every use.

Première utilisation

Using for the first time

System disconnected Rinsing the boiler

Always unplug the mains before

filling the boiler.

What sort of water to choose?

Getting started

Always fill the boiler with water before starting to iron as it could be damaged if heated up while empty.

CAUTION: Heating up without water invalidates your system’s guarantee.

Filling before using the system

Water hardness test included.

English

MagicEVO2-PreEVO2 Anglais.qxp 20.5.2009 9:53 Uhr Seite 5

Switches

Setting of the iron temperature

2. Turn on both switches and

wait until the green light comes

on (approx. 7 to 8 minutes).

1. Insert the plug.

8 min

Steam button

Vacuum / Blowing - choice of 2 speeds

A single steam control button situated on the iron allows you to both start the emission of steam and

switch from “blowing” mode to “vacuum” mode (or vice versa).

Changing from one mode to the other can be done only when the motor is off. The chosen mode stops

automatically at the end of a cycle (lasts 4 seconds). At that moment you may select the desired mode.

In addition to the vacuum and blowing functions, the steam control button enables the strength of the

flow of air from the ventilator to be regulated. When the iron is switched on, the ventilator is pre-set to

maximum capacity (100%). Changing from one mode to the other can be done only when the motor is off.

To change to reduced airflow (50%), press the steam control button twice very quickly. To go back to

maximum airflow, press the steam control button twice again.

Ironing

Position "A":

Normal temperature

Without Softpressing soleplate:

- cotton, linen.

With Softpressing soleplate:

- wool, silk, synthetics.

Position "B":

Low temperature

With Softpressing soleplate:

- for extremely delicate synthetics

eg: synthetic velours, Alcantara®

(synthetic suede), sport stretch

garments.

Check that the indicator light of the iron is also on before ironing.

ATTENTION:

After a change of setting it takes about 2 mins for the new temperature to stabilize!

If the iron spurts water, slightly increase the temperature.

Before starting to iron or after lengthy ironing interruption, press the steam button 2 or 3 times to evacu-

ate any water which may have condensed in the steam tube.

English

MagicEVO2-PreEVO2 Anglais.qxp 20.5.2009 9:53 Uhr Seite 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Laurastar premium evolution Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Laurastar premium evolution

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info