Bedienungsanleitung Lavazza LB 2800 (Seite 15 von 36) (Englisch)

495521

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Maintenance manual for technical assistance - LB 2800 - LB 2810

Manual code 10066574 / Rel. 0.00 / March 2009

3.4. Water connection

Inlet and outlet water connections should comply

with applicable laws in force in the country where

the machine is used.

- connect the water mains (2) to the inlet on the back

of the machine (6) using the hose provided. Then

open the tap of the water mains.

- connect the drain tub of the machine (4) to the sewer

drain (3) using the special tube provided. Take care to

avoid overly tight bends or kinks, and make sure that

there is sufficient inclination for water to flow out of

the drain..

Warning

Check that the surface prepared for the machine

installation, has dimensions and sturdiness suitable

to safely support the machine.

Note

or a correct ergonomic use of the machine, place

it on a working surface not lower than one meter

from the floor.

Warning

For correct operation, the machine must rest on a

perfectly horizontal surface. Any alignment adju-

stments of the machine must be done by adjusting

the feet.

Note

All filling connections are 3/8 male gas type. The

drain tub is connected with a tube with an internal

diameter of 16mm.

arning

Insert a tap (8) and a non-return valve (9)on the

water mains supply so that it will be possible to cut

off water flow to the machine.

Connect the water mains (2) directly to the inlet of

the machine (6). If you decide to install a water sof-

tener (11), connect the water mains (2) to the inlet

of the water softener, and the outlet of the water

softener to the inlet of the machine (6).

To prevent the water from freezing, install the sof-

tener (11), only in rooms with an ambient tempera-

ture of more than 5°C.

When connecting the tub of the machine to the

sewer drain, avoid overly tight curves or kinks, and

make sure that there is sufficient inclination for

water to flow out of the drain.

The drain must be connected to an inspectionable

siphon that can be periodically cleaned in order to

avoid the backflow of unpleasant odours.

To avoid oxidization and damage to the machine

over time, do not use iron connections for the

hydraulic connections, even if they are galvanized.

Attention

The hydraulic connection must be made in com-

pliance with local national standards.

If an external tank is used, the connection pipe

between the machine and the tank must not

exceed 150 cm.

For the European Community: for both the

hydraulic connection to the water mains as well

as the connection to an external tank, a non-

return valve (9) must be placed up the line from

the machine as set forth by standards EN 1717.

Warning

The water mains must provide cold water for

human consumption (potable water) at a maximum

pressure of 5 bar inclusive If the pressure is greater

than 5 bar, connect a pressure reducer upstream

from the pump.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lavazza LB 2800 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info