Bedienungsanleitung LD Systems RoadBoy 6.5 (Seite 15 von 122) (Deutsch, Englisch, Französisch, Italienisch, Spanisch, Polnisch)

622413

Zoom out

Zoom in

Vorherige Seite

1/122

Nächste Seite

ITALIANOPOLSKIESPAÑOL

FRANCAISFRANCAIS FRANCAISFRANCAIS

FRANCAISDEUTSCHENGLISH

SYSTEM SettInGS AnD oPeRAtIonS:

USING THE WIRED MICROPHONE INPUT

Plug the 6.3 mm Jack connector of your microphone cable into the MIC Jack input. You will ﬁnd this input on the

back panel of your Roadboy. Make sure that the other end of your cable is correctly connected to the microphone.

If your microphone features an ON / OFF switch, please set it to the ON position. Now use the MIC gain knob to set

the balance between the MIC and LINE inputs. Too much MIC level can cause distortion (Overdrive).

USING WIRELESS MODULE

Start by setting the MASTER level knob of your Roadboy on the zero position. Then turn the POWER-VOL knob of

the wireless module to twelve o’clock position. Now you can synchronize the transmitter (handheld mic or Belt

Pack) with the integrated receiver thanks to the ASC function: Press the ASC button of the wireless receiver modu-

le, the ASC LED now ﬂashes red.

If you are using a handheld transmitter: The Infrared sensor (IR) is placed in the battery compartment under

the capsule. Hold it close to the IR sensor of the wireless receiver module.

If you are using a Belt Pack transmitter: You need to activate the ASC function on the Belt Pack also. Then

hold the Infrared sensor (IR on the rear side) of the belt pack transmitter close to the IR window of the wireless

receiver module. The synchronization lasts a few seconds. If you have installed a second wireless module (opti-

onal), make sure that you are not running both modules on the same frequency in order to avoid any interference

(see frequency list). A ﬂashing RF light shows that your system is functioning and that the synchronization was

successful. You can now increase the MASTER volume of your Roadboy to the desired volume.

Maximum distance between the wireless microphone (or Belt Pack transmitter) and the receiver module is around

60 m in an open space.

USING THE „EXT. SPEAKER“ OUTPUT

Use a speaker cable with 6.3 mm Jack connector to connect the external loudspeaker. Use a speaker with impe-

dance between 4 and 8 Ohm with a minimal power output of 25 W.

CHARGING ROADBOY

Plug the power supply (16 V / 3 A) which is included with your Roadboy to operate your system without batteries

or in order to charge the batteries. The charging time is 8 hours. The charging procedure stops automatically when

the battery is fully charged. You can also keep the Roadboy connected to the AC current and operate it as long as

you wish.

IMPORTANT!

When connecting the battery for the ﬁrst time or when replacing the battery you MUST mind the

polarity! Red = + (plus) // Black = - (minus).

When the Roadboy is charged for the ﬁrst time, charging time should be 15 hours. This increases both

battery life and capacity. This procedure should be repeated every 2-3 months. Before this charging

procedure the battery should be empty.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

LD Systems RoadBoy 6.5 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info