Bedienungsanleitung Leen Bakker 81007837 Eurom (Seite 17 von 41) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch, Norwegisch)

821504

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

 Switch the heater on by turning the control dial to one of the following three positions:

800W, 1600W or 2400W. It is most economical to heat the space at full power, then to

switch to a lower power to maintain the temperature.

 At all powers, the fan rotates at the same speed; the difference lies in the number of

heating elements in use.

 Once the desired temperature is reached, turn the thermostat dial back slowly until you

hear a click. The temperature is now set. The heater will automatically switch on and off

to maintain the set temperature. To set a higher or lower temperature, turn the

thermostat dial either clockwise or anticlockwise.

 To switch the heater off, set the control dial to ‘0’ (off). Unplug.

Safety features

The heater is fitted with a tipping safeguard which automatically shuts off the appliance if it

inadvertently falls over. When the heater is returned to its upright position, it will resume

functioning as normal but, before reusing, switch off, unplug and check for damage. Do not

use the heater if it is damaged or malfunctioning, but have it inspected/repaired!

In case of internal overheating, the overheating safeguard will switch the heater off. This

may occur if the heater cannot give off enough heat or if it cannot draw in enough fresh air.

As mentioned above, this is generally caused by (partially) covering the heater, obstructing

the air intake and/or outlet grills or installing the heater too close to a wall or something

similar. When the overheating safeguard switches the heater off, set the mode selector dial

to ‘0’ (off), unplug and allow the heater to cool down. Remove and/or amend the cause of

overheating and reuse the heater as normal. If you cannot find a cause and overheating

recurs, stop using the heater, and take it in for inspection/repair.

Cleaning and Maintenance

Keep the heater clean. Deposits of dust and dirt in the appliance are a common cause of

overheating so these should be removed regularly. Switch off the heater, remove the plug

from the socket and allow the heater to cool down before cleaning or carrying out

maintenance work.

 Wipe the outside of the heater regularly with a dry or slightly damp cloth. Do not use

aggressive soaps, sprays, cleaners or abrasives, waxes, polishes or chemical solutions!

 Using a vacuum cleaner, carefully remove any dust and dirt from the grills and ensure

that the air intake and outlet openings are clean. Be careful not to touch or damage any

internal parts during cleaning!

 The heater contains no other parts which need maintenance.

 At the end of the season, store the cleaned heater in the original packaging if necessary.

Store it upright in a cool, dry and dust-free place.

 Do not dispose of heater with household waste when it becomes worn or

damaged beyond repair. Take it to your local authority's collection point for

electrical appliances where any reusable materials will be collected and

redistributed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Leen Bakker 81007837 Eurom Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info