Bedienungsanleitung Leifheit Vacu Power 100 (Seite 53 von 160) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

792735

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

The appliance does not automatically switch

to the sealing procedure after vacuuming:

• A negative pressure sensor is installed in this

appliance. The appliance does not change to

the sealing procedure automatically if the

vacuum pressure in the bag cannot reach the

specied vacuum pressure.

Check the sealing strips and the foam seals

under the cover for soiling and correct posi-

tion. Wipe clean and smooth them again.

Try again.

• Make sure that the foam seals on the cover

and on the base around the vacuum chamber

do not break or distort. Take this out of the

tray, wash and dry it thoroughly. Or replace it

with a new foam seal (obtain this from your

nearest service centre).

• The vacuum bag may have a leak. For testing,

seal the bag with a little air, immerse it in

water and apply pressure. Bubbles are an

indication that there is a leak. Seal the bag

again or use another one.

• Leaks may be along the seal that are caused

by folds, crumbs, grease of liquids. Open the

bag again, wipe out the top end of the bag

and smooth it along the sealing strip before

re-sealing.

Air enters the bag again after sealing:

• Leaks may be along the seal that are caused

by folds, crumbs, grease of liquids. Open the

bag again, wipe out the top end of the bag

and smooth it along the sealing strip before

re-sealing.

• Natural gases may be released or result in

fermentation of food products (such as fruit

and vegetables). Open the bag and if you

believe that the food is beginning to deterio-

rate, and throw it away. Insufcient cooling

or uctuating temperatures in the fridge may

lead to the food products deteriorating.

If the food product has not deteriorated, these

should be consumed immediately.

• Check the bag for damage or a hole that may

allow the vacuum to escape.

Do not vacuum hard objects with sharp tips.

Pad sharp edges with paper towels in order to

avoid damage.

The bag melts:

• If the sealing strip or the sealing element

overheats and brings the bag to melt, the

cover may have to be raised to allow the

sealing strip of the heating element to cool

down for a few minutes.

A vacuum is not generated in the container:

• Make sure that the connecting hose is con-

nected tight with the appliance and container.

• At the beginning of the vacuuming procedu-

re, press on the container lid OR on the hose

adapter in order to prevent the container seal

from leaking.

• Check if there is any damage. If yes, replace

the damaged parts with new ones.

• Check the function of the vacuuming appli-

ance.

• Make sure that the edge of the container is

clean enough. If all situations mentioned

above have been ruled out, please contact

the service centre specied.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Leifheit Vacu Power 100 Seite 53

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info