Bedienungsanleitung Lenco KDV-310 (Seite 7 von 10) (Englisch)

534769

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

GB-6

4. SPEAKER SETUP

4.1 DOWNMIX

Options: LT/RT - Left/Right mix mode

STEREO - Stereo mode

4.2 EXIT SETUP - Select it to exit the setup menu.

RADIO OPERATION

TO PLAY THE RADIO

1. Press FUNCTION button repeatedly to switch to RADIO

mode (At the moment, the TFT display will be turned off), the

radio Indicator will light up and the LCD shows the current

frequency and band.

2. Select the desired band with STOP/BAND button until your

desired band shows in the LCD.

3. Tune to the desired station by pressing TUNE UP/DOWN

button (Press TUNE UP/DOWN button repeatedly until you

get the strongest clearest sound).

4. When receiving a FM ST station, the relative icon will show in

the LCD.

5. The AM antenna and external FM ANTENNA are directional.

y When receiving an FM broadcast, unfold the FM antenna

and place it in the best position for the best reception.

y For AM broadcasts, rotate AM antenna until the best

reception is heard.

There are two clips on the AM antenna in. Press these

two clips to connect the AM antenna easily as the

illustration for AM reception.

6. Adjust the volume level to a comfortable listening level.

7. Press the POWER button to turn off the radio.

Note: If a particular FM (STEREO) station is weak, or you hear

too much background noise, press ANGLE/ST/MONO button

on the remote to switch FM (MONO). This can often result in a

much clearer reception.



TO STORE THE RADIO STATION (UP TO 10 FOR AM / 30

FOR FM)

1. Press BAND button to select your desired band and tune to

your favorite station via TUNE UP/DOWN button.

2. Press memory button and select the stored position via MEM

UP/DOWN button.

3. Press MEMORY button to save the radio station and exit the

memory mode.

Note: The relative information will be shown in the LCD during

the procedures of saving radio station.

To recall the saved station, Press MEM UP/DOWN button

directly to select your desired station saved in the memory for

listening.

SET TIME

Please set time as the below procedure:

1. Press standby button to switch to standby mode and press

CD DOOR OPEN/CLOSE button on the unit, the hours

flickers for adjusting.

2. Press NEXT/TUNE UP button or PREVIOUS/TUNE DOWN

button to adjust hour.

3. After adjustment, press CD DOOR OPEN/CLOSE button

again to confirm and the minute flashes for adjusting.

4. Use NEXT/TUNE UP button or PREVIOUS/TUNE DOWN

button to adjust minute.

5. Finally, press OK button to save the time.

Note: You only could set time in standby mode.

ALARM OPERATION

The unit is with alarm function, you could set alarm as below

steps in standby mode:

1. Press and hold ALARM button on the unit until the hour

flashes in the LCD with the flickering alarm icon.

2. Press NEXT/TUNE UP button or PREVIOUS/TUNE DOWN

button to adjust hour.

3. Press ALARM button to confirm. And the minute flashes to

wait for you adjust.

4. Use NEXT/TUNE UP button or PREVIOUS/TUNE DOWN

button to adjust minute.

5. Press ALARM button again to save.

6. Use NEXT/TUNE UP button or PREVIOUS/TUNE DOWN

button to select the alarm mode (b b- when the alarm comes

on, the unit will sound Bi Bi... Fun- when the alarm comes on,

the unit will be turned on.)

7. Finally, use ALARM button to save all settings.

Press ALARM button to enable or disable the function. The

LCD show Alarm icon while the alarm is on.

Note: The alarm only could be set in standby mode.

SET TIMER

The timer function is used to time for reminding while cooking.

Set the timer as below procedures:

1. Press TIME button repeatedly to select the approximate time

among 10, 15, 30, 45, 60, 75, 90, 180, OFF.

2. Then use TUNE UP/DOWN button to increase or decrease

the minute for exact time

3. Press OK button to confirm.

When it reminds with sound, press TIME button to stop it.

After setting the timer, press COUNT DOWN button on the unit

or COUNT DOWN button on the remote to check the remain

time.

DVB OPERATIONS

GET STARTED

y Be sure the TV antenna is connected to your player

properly;

y Power on the player and press FUNCTION button several

times to switch to DVB-T mode and DVD/DVB-T indicator is

lit.

A dialogue of first time installation shows on the screen, select

YES option to perform the first time installation, then select the

options as mentioned in the dialogue to finish the first time

installation, select NO option to exit this interface.

LANGUAGE

Press AUDIO button on the remote repeatedly to select

preferred audio language by TV programs provided during DVB

mode.

DISPLAY PROGRAM DETAIL INFORMATION

Press DISPLAY button during DVB play mode to show the

program detail information.

ELECTRONIC PROGRAM GUIDE

Press Program/EPG Button during DVB play mode to skim

over TV Programs guide.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lenco KDV-310 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Lenco KDV-310

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info