Bedienungsanleitung Lenco LS-101 (Seite 7 von 85) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

792703

Zoom out

Zoom in

Vorherige Seite

1/85

Nächste Seite

SET UP

An AC/DC adaptor with an output of 12V DC 2.0A is included with this Turntable with Bluetooth reception and

Wooden Speakers. The adaptor is required for operating the unit.

Connect the speaker cables from each speaker to the back of the unit

Note: The external speaker cables are color coded, the cable with the red connector should be put in the red

hole and the white one in the white hole.

Firmly and securely insert the DC plug of the adaptor to the DC IN Jack on the back of the unit.

Plug the adaptor’s AC plugs into a power outlet rated at 220-240V AV ~ 50 Hz.

Turn on the unit by the POWER/VOLUME Knob. The Power/Function Led Light Indicator will turn on.

Remark: To avoid Larsen effect or Feedback noise, you can do the following:

1. Put your speakers at minimum distance of 60 cm or more from your turntable

2. Keep the dustcover open when you play a record at higher sound volume

Power On and Mode selection

Turn on the unit by the POWER/VOLUME Knob. You will hear a click sound and the Power/Function Led Light

Indicator will turn on confirming the power is ON. When the power is ON, you can rotate the control normally

to adjust the volume of the music playing.

Rotate the FUNCTION SELECTOR to difference modes ( OUT/PHONO/AUX/ IN).

2. Listen to a Record

1. Raise the dust cover

2. Turn on the unit by the POWER/VOLUME Knob. The Power/Function Led

Light Indicator will light in RED at PHONO mode.

3. Or you can rotate FUNCTION SELECTOR to PHONO mode.

4. Place a record on the turntable platter and set the player speed to match

the record speed.

Note: When playing a single (a 45 rpm record) and/or records with large

centre holes, use the 45 rpm adaptor.

5. Remove the needle cartridge protective cover

Unlock the tone arm lock from the tone arm rest. Push the lift lever backward, the tone arm will gently rise up.

Gently move the tone arm to the desired position over the record and the turntable platter will begin to rotate

when the arm is moved towards it If Auto Stop Control Switch in ON. Release the tone arm onto the turntable

by pushing the lift lever forward and the vinyl record will begin to play.

If the Auto Control Switch is turned ON, the record will stop automatically when finished. If Auto Stop Control

Switch is turned OFF, the record will NOT stop automatically when finished; you must push the lift lever

backward to raise the tone arm and place it back in the rest and then turn off the power to stop the turntable

from spinning.

Remark: AUTO STOP function applies to most 33RPM vinyl records. However, for very few vinyl records, it will

stop when it does not come to the end, or it will not stop when it comes to the end when AUTO STOP is ON.

NOTE: If your record stops before the last track finishes, set the AUTO STOP switch to OFF. Your record will now

play to the end, but you will have to stop the turntable rotation manually.

NOTE: Depending on the record length, AUTO STOP may be enabled before the end of the recording.

Do not rely on AUTO STOP alone to turn off playback.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lenco LS-101 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info