Bedienungsanleitung Lenco SCD-1900 (Seite 6 von 60) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

601868

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

EN-5

2. "T" shows on the LCD display with hour flashing. Adjust the hour by pressing SLEEP/HR/MIN button

on the unit continuously and press TIMER Button to confirm.

3. The minute flashes on the display. Set the minute by pressing SLEEP/HR/MIN button on the unit

continuously. Confirm your setting by pressing TIMER button. The timer “ON” shows on the display

to indicate the timer is activated (Press TIMER button again to disable the timer).

Note: When the hour or minute flashes on the display, the time can also be set by pressing HR

button or MIN button on the remote directly. After setting, press TIMER button to confirm.

4. The unit will be turned on automatically at the time you set for the timer.

FM RADIO

TUNING THE FM RADIO

1. Press STANDBY button to turn the unit on.

2. Press FUNCTION button on the unit repeatedly or press FM button on the remote to switch the unit

to FM mode.

3. Press TUNING+/- button to fine tune the radio station. Press and hold TUNING+/- button to

automatically tune the radio frequency forward and backward respectively. When an available station

is found, the unit will broadcast it immediately.

4. Press the PLAY/PAUSE button on the unit or ST/MO button on the remote to switch the radio

between MONO and STEREO.

5. Fully extend the telescopic antenna and adjust its direction for best radio reception.

SAVING FM RADIO STATIONS TO THE UNIT'S MEMORY

1. After tuning the FM radio to the desired stations, press MEM button, a number of a memory cell

flashes on the screen.

2. Press CHANNEL+/- button to select the radio memory cell.

3. Press MEM button again to save the current radio station to the selected memory cell. Up to 20 FM

radio stations can be saved.

4. To recall the preset station frequency, press CHANNEL+/- button repeatedly.

HANDLING AND MAINTENANCE OF A DISC

Follow the instructions below to handle and maintain your disc in order

that long time and trouble free performance can possibly be obtained:

 Ensure not to caress the rain bow side of the disc; handle the disc by

the edge.

 Long time exposure to sunshine, high temperatures and humidity will

damage the disc. And keep storage area clean.

 Avoid sticking labels on both sides of a disc. Writing with pointed

articles on the disc should be strictly avoided.

 Clean the disc wiping the centre and then working out to the edge

with a dry & soft cloth or a disc brush. Avoid any cleansing lotion or

chemical eradicator.

 Store them in their cases when they are not to be used.

LOAD A DISC

1. Open the CD door by pressing the PUSH TO OPEN area.

2. Load a disc on the disc tray with the label side facing outside.

3. Close the CD door.

PLAY A DISC

1. Follow the instructions above to load a disc.

2. Press the FUNCTION button on the unit repeatedly or press CD button on the remote to switch the

unit to CD mode. "READING" shows on the screen to indicate the disc is being read.

3. When the disc is read successfully, playback will start from the first track.

HANDLE DISC ONLY AS SHOWN

CLEAN FROM CENTER TO EDGE

DO NOT STORE NEAR HEAT

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lenco SCD-1900 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info