214280
20
Zoom out
Zoom in
Vorherige Seite
1/62
Nächste Seite
described directly above (the yellow connectors on the video cable are not used).
computer 1
computer 2
video
monitor
network
serial control
audio in
audio in
audio in
audio out
R
R
L
L
Y
Pr
Pb
s-video
computer in
If the video device uses component cable connectors (sold separately), plug the
cable’s green connectors into the green component-out connector on the video
device and into the green component connector (labeled Y) on the projector. Plug
the component cable’s blue connectors into the blue component- out connector on
the video device and into the blue component connector (labeled Pb)onthe
projector. Plug the component cable’s red connectors into the red component-out
connector on the video device and into the red component connector (labeled Pr)
on the projector. Use the video cable’s audio connectors as described directly above
(the yellow connectors on the video cable are not used).
computer 1
computer 2
video
monitor
network
serial control
audio in
audio in
audio in
audio out
R
R
L
L
Y
Pr
Pb
s-video
computer in
Displaying a video image
To display a video image:
1. Remove the lens cap.
2. Press the Power button on the top of the projector.
The LED flashes green and the fans start to run. When the lamp comes on, the
startup screen is displayed and the LED is steady green. It can take a minute
for the image to achieve full brightness. If you do not see a startup screen see
Appendix B, “Troubleshooting your setup”, on page 27.
3. Plug in and turn on the video device.
The video device’s image should appear on the projection screen. If it does not,
press the Video button.
4. Position the projector the desired distance from the screen at a 90 degree angle
to the screen.
5. Adjust the zoom or focus rings by rotating them until the desired image size
and sharpness are produced.
6. If the image is not square, adjust the keystone using the buttons on the keypad.
Press the upper Keystone button to reduce the upper part of the image, and
press the lower Keystone button to reduce the lower part.
7. Adjust the volume on the keypad or the remote.
10 IBM iLC300 Conference Projector: IBM iLC300 Conference Projector User’s Guide
20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Lenovo ilc300 conference room wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info