20464
106
Zoom out
Zoom in
Vorherige Seite
1/145
Nächste Seite
Restoring factory default settings
106
Administrative support
Restoring factory default settings
When first entering the printer menus from the operator panel, notice an asterisk (*) next to a value in the menus. This
asterisk indicates the factory default setting. These settings are the original printer settings. (Factory defaults may vary for
different countries and regions.)
When a new setting is selected from the operator panel, the Saved message appears. When the Saved message
disappears, an asterisk appears next to the setting to identify it as the current user default setting. These settings are active
until new ones are stored or the factory defaults are restored.
To restore the original printer factory default settings:
1 Make sure the printer is on and the Ready message appears.
2 Press to enter the menus.
3 Press until Settings appears, and then press .
4 Press until Setup Menu appears, and then press .
5 Press until Factory Defaults appears, and then press .
6 Press until Restore Now appears, and then press .
The message Restoring Factory Defaults appears, followed by the Ready message.
When Restore is selected:
No other button actions are available on the operator panel while Restoring Factory Defaults appears.
All downloaded resources (fonts, macros, and symbol sets) in printer memory (RAM) are deleted. (Resources
residing in flash memory or on the optional hard disk are unaffected.)
All menu settings are returned to the factory default values, except:
The operator panel Display Language setting in the Setup Menu.
All settings in the Parallel Menu, Serial Menu, Network Menu, and USB Menu.
Adjusting Power Saver
To adjust the Power Saver setting in the Setup Menu:
1 Make sure the printer is on and the Ready message appears.
2 Press to enter the menus.
3 Press until Settings appears, and then press .
4 Press until Setup Menu appears, and then press .
5 Press until Power Saver. appears, and then press .
6 Press or to decrease or increase the number in the scale for the desired number of minutes, and then
press .
Minute settings available range from 1240. The menu value Disabled is also available if Energy Conserve is
set to Disabled.
The Submitting Selection message appears.
Note: The Power Saver setting may also be adjusted by issuing a Printer Job Language (PJL) command.
For more information, see the Technical Reference available on our Lexmark Web site at
www.lexmark.com.
106

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Lexmark C522 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Lexmark C522

Lexmark C522 Bedienungsanleitung - Holländisch - 35 seiten

Lexmark C522 Bedienungsanleitung - Spanisch - 152 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info