20690
83
Zoom out
Zoom in
Vorherige Seite
1/143
Nächste Seite
83
Remove Cartridge and
ITU Packaging
The packing material has not been
removed from the cartridges and the
image transfer unit belt.
Remove all packing material from inside
the printer.
See also: “Step 5: Installing Supplies” in
the Setup Guide
Remove Paper
<specified bin>
The specified output bin, or bins, is full. Remove the stack of paper from the
specified bin(s) to clear the message.
Resetting Active Bin
The printer is resetting to the active bin
in a linked set of bins.
Wait for the message to clear.
Resetting Fuser Cnt
Value
The printer is resetting the counter that
tracks wear on the fuser.
Wait for the message to clear.
Resetting the Printer
The printer is resetting to the current
default settings. Any active print jobs
are canceled.
Wait for the message to clear.
See also: Changing menu settings
Restore Held Jobs.
Go/Stop?
Someone reset the printer or turned it
on, and the printer detects Print and
Hold jobs stored on the hard disk.
•Press Go. All Print and Hold jobs on the
hard disk are restored to printer memory.
•Press Return or Stop. No Print and
Hold jobs are restored to printer
memory. The printer returns to the
Ready state.
See also: Holding a job in the printer
Restoring Factory
Defaults
The printer is restoring the factory
default printer settings. When factory
default settings are restored:
All downloaded resources (fonts,
macros, symbol sets) in the printer
memory are deleted.
All menu settings return to the
factory default setting except:
The Display Language setting in
the Setup Menu.
All settings in the Parallel Menu,
Serial Menu, Network Menu,
USB Menu, and Fax Menu.
Wait for the message to clear.
See also: Restoring factory default
settings
Restoring Held Job
xxx/yyy
The printer is restoring held jobs from
the hard disk.
Note: xxx represents the number of
the job being restored. yyy represents
the total number of jobs to be restored.
Wait for the message to clear.
Select the Abort Restore menu item in
the Job Menu.
See also: Holding a job in the printer
Restoring Held Jobs
The printer is restoring held jobs from
the hard disk.
Wait for the message to clear.
See also: Holding a job in the printer
Serial <x>
A serial interface is the active
communication link.
Wait for the message to clear.
Setup Required
Press Go
When you unpacked the printer, you
left a piece of packing material
inside.
Remove all packing material from inside
the printer.
After pressing Go, you may see the
message, “Remove Cartridge and ITU
Packaging.
See also: Remove Cartridge and ITU
Packaging; “Step 5: Installing Supplies” in
the Setup Guide.
Message What this message means What you can do
83

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Lexmark C762 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Lexmark C762

Lexmark C762 Bedienungsanleitung - Holländisch - 218 seiten

Lexmark C762 Bedienungsanleitung - Portugiesisch - 44 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info