Bedienungsanleitung Lexmark CS517 (Seite 56 von 229) (Englisch)

670897

Zoom out

Zoom in

Vorherige Seite

1/229

Nächste Seite

Weight

The printer trays can automatically feed paper weights up to 176‑g/m

(47‑lb) bond grain long paper. The

multipurpose feeder can automatically feed paper weights up to 176‑g/m

(47‑lb) bond grain long paper. Paper

lighter than 60 g/m

(16 lb) might not be sti enough to feed properly, causing jams. For best performance, use

75‑g/m

(20‑lb) bond grain long paper. For paper smaller than 182 x 257 mm (7.2 x 10.1 inches), we recommend

90 g/m

(24 lb) or heavier paper.

Note: Duplex printing is supported from 60–105‑g/m

(16–28‑lb) bond grain long paper.

Curl

Curl is the tendency for paper to curl at its edges. Excessive curl can cause paper feeding problems. Curl can

occur after the paper passes through the printer, where it is exposed to high temperatures. Storing paper

unwrapped in hot, humid, cold, or dry conditions, even in the trays, can contribute to paper curling prior to

printing and can cause feeding problems.

Smoothness

Paper smoothness directly aects print quality. If paper is too rough, then toner cannot fuse to it properly. If

paper is too smooth, then it can cause paper feeding or print quality issues. Always use paper between 100

and 300 Sheeld points; smoothness between 150 and 250 Sheeld points produces the best print quality.

Moisture content

The amount of moisture in paper aects both print quality and the ability of the printer to feed the paper correctly.

Leave paper in its original wrapper until it is time to use it. This limits the exposure of paper to moisture changes

that can degrade its performance.

Store paper in its original wrapper in the same environment as the printer for 24 to 48 hours before printing.

Extend the time to several days if the storage or transportation environment is very dierent from the printer

environment. Thick paper may also require a longer conditioning period.

Grain direction

Grain refers to the alignment of the paper ﬁbers in a sheet of paper. Grain is either grain long, running the length

of the paper, or grain short, running the width of the paper.

For 60–90‑g/m

(16–24‑lb) bond paper, grain long paper is recommended.

Fiber content

Most high‑quality xerographic paper is made from 100% chemically treated pulped wood. This content provides

the paper with a high degree of stability resulting in fewer paper feeding problems and better print quality.

Paper containing ﬁbers such as cotton can negatively aect paper handling.

Unacceptable paper

The following paper types are not recommended for use with the printer:

• Chemically treated papers used to make copies without carbon paper, also known as carbonless papers,

carbonless copy paper (CCP), or no carbon required (NCR) paper

• Preprinted papers with chemicals that may contaminate the printer

• Preprinted papers that can be aected by the temperature in the printer fuser

Paper and specialty media guide 56

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lexmark CS517 Seite 56

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Lexmark CS517

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info