Bedienungsanleitung LG 50PA4500 (Seite 50 von 52) (Englisch)

495686

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

ENG

ENGLISH

EXTERNAL CONTROL DEVICE SETUP

01: Minimum

02: Medium

03: Maximum

04: Intelligent Sensor

05: Screen off

Acknowledgement [q][ ][Set ID][ ][OK/NG][Data][x]



To adjust picture position and minimize image shaking

automatically. Auto configuration only works in RGB-PC

mode.

Transmission [ j ][u][ ][Set ID][ ][Data][Cr]

Data 01: To set

Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]



To tune channel to following physical/major/minor

number.

(This feature is not available for all models.)

Transmission [m][a][ ][Set ID][ ][Data00][ ][Data01]

[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]

Digital channels have a Physical, Major, and Minor

channel number. The Physical number is the actual

digital channel number, the Major is the number that the

channel should be mapped to, and the Minor is the sub-

channel. Since the ATSC tuner automatically maps the

channel to the Major number, the Physical number is not

required when sending a command.

Data 00: Physical Channel Number

NTSC air: 02~45, NTSC cable: 01, 0E~7D

ATSC air: 01~45, ATSC cable: 01~87

Data 01 & 02: Major Channel Number

Data 01: High byte Data 02: Low byte

Two bytes are available for the Major and Minor,

normally only the second byte is used.

Data 03 & 04: Minor Channel Number

Not needed for NTSC.

The table lists the binary code which must be converted

to Hexadecimal before sending. For example:

The binary code to tune the sub source to an NTSC cable

channel is “1000 0001”, which translates to “81” in

Hex.

* 7th bit : For which source do you want to change

the channel.

* 6th bit: Use a two part or one part channel. Most

cases just use 0 since it’s ignored when using

NTSC.

* 5th bit: Use 0 with NTSC since it can only use

the physical channel number. Normally use 1 for

ATSC since most times it doesn’t matter what the

physical number is.

* 4th bit: Set to 0.

* 3-0 bits: Choose signal type.

* Tune Command Examples:

1. Tune to the analog (NTSC) cable channel 35.

Data 00 = Physical of 35 = 23

Data 01 & 02 = No Major = 00 00

Data 03 & 04 = No Minor = 00 00

Data 05 = 0000 0001 in binary = 01

Total = ma 00 23 00 00 00 00 01

2. Tune to the digital (ATSC) local channel 30-3.

Data 00 = Don’t know Physical = 00

Data 01 & 02 = Major is 30 = 00 1E

Data 03 & 04 = Minor is 3 = 00 03

Data 05 = 0010 0010 in binary = 22

Total = ma 00 00 00 1E 00 03 22



To add and delete the channels.

Transmission [m][b][ ][Set ID][ ][Data][Cr]

Data 00: Channel Delete Data 01: Channel Add

Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]



To send IR remote key code.

Transmission [m][c][ ][Set ID][ ][Data][Cr]

See page 3.

Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]

When TV is in the standby mode, TV will turn on by

POWER button of remote control only.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

LG 50PA4500 Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von LG 50PA4500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info