Bedienungsanleitung Liebherr CBNES 3967 (Seite 9 von 26) (Englisch)

76953

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Fig. 12

Slide the faceplate forwards over the soft stop bracket

Fig. 12 (34)

in the direction of the appliance.

Snap the safety lock

Fig. 12 (32)

into the oblong hole.

The safety lock prevents the hinge from snap-closing.

Using a screwdriver, lift off the cover

Fig. 12 (31)

from the

outside and remove it in an outward direction.

If necessary, tip the appliance backwards with the assis-

tance of a second person.

Press the pin

Fig. 12 (33)

out from underneath.

Press the soft stop bracket

Fig. 12 (34)

towards the door.

Remove the faceplate

Fig. 12 (30)

Unscrew the soft stop unit (2x Torx® 15)

Fig. 12 (35)

Pull the soft stop unit out a little, push it in the direction of the

handle side and swing it out.

Set the soft stop unit aside.

4.3.5 Detaching the lower door

Close the lower door.

For appliances without soft stop mechanism:

Draw the middle bearing pin

Fig. 13 (41)

out of the turn

hinge and lower door.

For appliances with soft stop mechanism:

Draw the middle bearing pin

Fig. 13 (41)

together with the

washer

Fig. 13 (44)

out of the turn hinge and lower door.

For all appliances:

Remove the plastic cap

Fig. 13 (40)

CAUTION

Risk of injury if the door tips!

Take good hold of the door.

Set down the door carefully.

Open the lower door.

Unscrew the middle turn hinge (2x Torx® 25).

Fig. 13 (42)

Lift off the lower door and set it aside.

4.3.6 Transferring the middle bearing elements

Fig. 13

Carefully detach the cover panel

Fig. 13 (43)

Turn the middle turn hinge

Fig. 13 (42)

with thewasher

Fig. 13 (45)

through 180° and screw it firmly into place on

the new hinge side (with 4 Nm).

Turn the cover panel

Fig. 13 (43)

through 180° and snap it

into place again on the new handle side.

4.3.7 Transferring the lower bearing elements*

for appliances without soft stop mechanism

Fig. 14

Lift out the bearing pin

Fig. 14 (52)

together with washer

Fig. 14 (53)

and adjustable-height foot

Fig. 14 (54)

Lift off the stopper

Fig. 14 (51)

Unscrew

Fig. 14 (56)

the turn hinge

Fig. 14 (55)

Unscrew

Fig. 14 (59)

the bearing element

Fig. 14 (58)

transfer it to the opposite location hole of the turn hinge and

screw it firmly into place.

Carefully lift off the cover on the handle side

Fig. 14 (57)

and

transfer it to the opposite side.

Screw the turn hinge

Fig. 14 (55)

firmly into place on the

new hinge side, possibly using a cordless screwdriver (with

4 Nm).

Re-insert the stopper

Fig. 14 (51)

into the other hole.

Re-insert the bearing pin

Fig. 14 (52)

together with the

washer and adjustable-height foot. In so doing, pay attention

that the locating lug points backwards

4.3.8 Transferring the lower bearing elements *

for appliances with soft stop mechanism

Fig. 15

Lift out the bearing pin

Fig. 15 (52)

together with washer

Fig. 15 (45)

and adjustable-height foot

Fig. 15 (54)

Lift out the stopper

Fig. 15 (51)

Putting into operation

* Depending on model and options 9

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr CBNES 3967 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr CBNES 3967

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info