Bedienungsanleitung Liebherr CBNes 5778 (Seite 8 von 36) (Englisch)

715295

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

NOTICE

Risk of damage from stainless steel care products!

The stainless steel doors and stainless steel side panels

are treated with a premium surface finish.

Stainless steel care products attack these surfaces.

uOnly use a soft, clean cloth to wipe down finished door

and side panel surfaces and painted door and side panel

surfaces. To remove heavy dirt, use a little water or

neutral detergent. Alternatively, you can use a micro-fibre

cloth.

uRemove the protective film from the decorative trims and

drawer fronts.

uRemove all transit supports.

Spacers must be used to achieve the declared energy

consumption and to prevent condensation in the event of

high surrounding humidity. This increases the appliance

depth by about 15 mm. The appliance will work perfectly

well without the spacers but will have a slightly higher

energy consumption.

uIf your appliance comes with

wall spacers, mount these on

the back of the appliance,

bottom left and right.

uDispose of packaging material (see 4.5 Disposing of

packaging) .

CAUTION

Risk of injury or damage from the appliance tipping or the

door falling open!

If the additional adjustable foot on the base support is not

correctly positioned on the floor, there is a risk of the door

falling open or the appliance tipping. This can lead to injury

or property damage.

uUnscrew the additional adjustable foot on the support

until it reaches the floor.

uThen turn it another 90°.

uAlign the appliance so that it

stands firmly and on a level

by applying the accompa‐

nying spanner to the adjust‐

able-height feet (A) and

using a spirit level.

uThen support the door:

Extend the adjustable foot

at the turn hinge (B) until it

rests on the floor and then

make a further 90° turn.

Note

uClean the appliance (see 6.4 Cleaning the appliance) .

If the appliance is installed in a very damp environment,

condensate may form on the outside of the appliance.

uAlways see to good ventilation at the installation site.

4.3 Reversing the door

If necessary, you can change the way the door opens:

Ensure that the following tools are available:

qTorx® 25 (T25)

qTorx® 15 (T15)

qSlotted screwdriver

qOpen-ended wrench SW10

qSpirit level

qOpen-ended wrench supplied with the T25 tool

qIf necessary, a cordless screwdriver

qGet a stepladder if necessary

qIf necessary, a second person for assembly

4.3.1 Remove the upper soft stop mechanism*

Fig. 10

uOpen the top door.

NOTICE

Risk of damage!

If the door seal is damaged, the door may fail to close prop‐

erly and the cooling will be inadequate.

uDo not damage the door seal with the screwdriver!

uRemove the outer cover. Fig. 10 (1)

uDisengage and release the bearing bracket cover.

Remove the bearing bracket cover. Fig. 10 (2)

uUnlatch the panel with a slotted screwdriver and swivel it

to one side. Fig. 10 (3)

Fig. 11

Putting into operation

8 * Depending on model and options

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr CBNes 5778 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr CBNes 5778

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info