Bedienungsanleitung Liebherr CBNPes 5156 Premium (Seite 7 von 18) (Englisch)

597391

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

Carefully detach the cover panel

Fig. 5 (12)

Turn the middle turn hinge

Fig. 5 (13)

with the washer

Fig. 5 (14)

through 180° and screw it firmly into place on the

new hinge side (with 4 Nm).

Turn the cover panel

Fig. 5 (12)

through 180° and snap it

into place again on the new handle side.

4.3.4 Transferring the lower bearing elements

Fig. 6

Lift out the bearing pin

Fig. 6 (22)

together with washer

Fig. 6 (23)

and foot

Fig. 6 (24)

Lift off the stopper

Fig. 6 (21)

Unscrew

Fig. 6 (26)

the turn hinge

Fig. 6 (25)

Unscrew

Fig. 6 (29)

the bearing element

Fig. 6 (28)

, transfer

it to the opposite location hole of the turn hinge and screw it

firmly into place.

Carefully lift off the cover on the handle side

Fig. 6 (27)

and

transfer it to the opposite side.

Screw the turn hinge

Fig. 6 (25)

firmly into place on the new

hinge side, possibly using a cordless screwdriver (with

4 Nm).

Re-insert the stopper

Fig. 6 (21)

into the other hole.

Re-insert the bearing pin

Fig. 6 (22)

together with washer

and foot. In so doing, pay attention that the locating lug

points backwards

4.3.5 Transferring the handles

On both the upper and lower door:

Transfer the spring clamp

Fig. 7 (31)

: Depress the

latch nose and pull the

spring clamp off over it.

Slide the spring clamp

into place on the new

hinge side until it clicks

into place.

Fig. 7

Fig. 8

Lift the stopper

Fig. 8 (30)

out of the door bearing bush and

transfer it.

Detach door handle

Fig. 8 (32)

, stopper

Fig. 8 (33)

and pres-

sure plates

Fig. 8 (34)

and transfer to the opposite side.

When fitting the pressure plates on the opposite side, make

sure they snap properly into place*

4.3.6 Fitting the lower door

Place the lower door from above onto the lower bearing pin

Fig. 6 (22)

Close the door.

Place the plastic cap

Fig. 5 (10)

back onto the middle turn

hinge

Fig. 5 (13)

Place the middle bearing pin

Fig. 5 (11)

in the lower door, on

the new hinge side, through the middle turn hinge

Fig. 5 (13)

4.3.7 Fitting the upper door

Place the upper door on the middle bearing pin

Fig. 5 (11)

Insert the upper turn hinge

Fig. 4 (3)

in the door on the new

hinge side.

Screw the upper turn hinge firmly into place (with 4 Nm)

(2x Torx® 25)

Fig. 4 (4)

. Possibly make preliminary holes

with a bradawl or use a cordless screwdriver.

Apply the cover

Fig. 4 (1)

and cover

Fig. 4 (2)

to the oppo-

site side from the outside and snap them into place.

4.3.8 Aligning the doors

If necessary, align the doors to the appliance housing by

way of the two oblong holes in the bottom turn hinge

Fig. 6 (25)

and middle turn hinge

Fig. 5 (13)

. To do so,

unscrew the middle screw in the bottom turn hinge

Fig. 6 (25)

WARNING

Risk of injury due to the door dropping out!

If the bearing parts are not screwed into place firmly enough,

the door may drop out. This may lead to severe injuries. What

is more, the door may not close and therefore the appliance

may fail to cool properly.

Screw the turn hinges firmly into place with 4 Nm.

Check all of the screws and retighten if necessary.

Putting into operation

* Depending on model and options 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr CBNPes 5156 Premium Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr CBNPes 5156 Premium

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info