Bedienungsanleitung Liebherr CN 4213 (Seite 5 von 11) (Englisch)

715299

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

Putting into operation

* according to model and design

4.4 Insertion into a row of kitchen units

The appliance can be tted into kitchen units.

u see assembly instructions provided.

Ventilation requirements:

A [mm] B [mm] C [cm

] D [mm] E [mm]

655

75 min. 300 min. 50 min. 19

This dimension increases by 35 mm in case of appliances with

wall spacer brackets attached (see 4.2).

The appliance may protrude further, depending on the depth of

the kitchen units and the use of wall spacer brackets.

ATTENTION

Risk of damage to the appliance due to overheating with

insucient ventilation!

The compressor may be damaged with insucient ventilation.

u Ensure sucient ventilation.

u Observe the ventilation requirements.

4.5 Disposing of packaging

WARNING

Danger of suocation due to packing material and

plastic lm!

u Do not allow children to play with packaging material.

The packaging is made of recyclable materials:

- corrugated board/cardboard

- expanded polystyrene parts

- polythene bags and sheets

- polypropylene straps

- nailed wooden frame with polyethylene panel*

u Take the packaging material to an ocial collecting point.

4.6 Connecting the appliance

NOTICE

Failure to connect properly

Damage to the electronics.

u Do not use a standalone inverter.

u Do not use an energy saving plug.

WARNING

Failure to connect properly Fire.

u Do not use an extension cable.

u Do not use distributor blocks.

The type of current (alternating current) and voltage at the

installation site have to conform with the data on the type plate

(see Appliance at a glance).

The socket must be properly earthed and fused. The tripping

current for the fuse must be between 10 A and 16 A.

The socket must be easily accessible so that the appliance can

be quickly disconnected from the supply in an emergency. It must

be outside the area of the rear of the appliance.

u Check the electrical connection.

u Plug in the power plug.

4.7 Switching on the appliance

Note

u To switch on the entire appliance it is necessary only to switch

on the freezer compartment. In so doing, the refrigerator

compartment is automatically switched on as well.

The appliance should have been operating for about 2 hours

before you stock it with frozen food. Only place frozen goods in

the freeze compartment once the temperature display shows at

least -18°C.

q Do not install the appliance in a location where it is exposed to

direct radiation of the sun, next to a cooker, heater and similar.

q Always stand the appliance backed directly to the wall using

the enclosed wall spacers (see below).

q The appliance may be moved only when it is empty.

q The surface supporting the appliance must be at the same

level as the surrounding oor.

q Do not install the appliance without assistance.

q The more coolant there is in the appliance, the larger the

room in which the appliance is installed must be. If the room

is too small, any leak may create a ammable mixture of gas

and air. For each 8 g of coolant the installation space must

be at least 1 m3. Information on the coolant is on the model

plate inside the appliance.

u Detach the connecting cable from the rear of the appliance,

removing the cable holder at the same time because

otherwise there will be vibratory noise!

u Remove the protective lm from the outside of the appliance.*

u Remove all transit supports.

The spacers supplied with some appliances must be used to

achieve the stated energy consumption. These will extend the

depth of the appliance by approx. 35 mm. The appliance is fully

functional if the spacers are not used, but does have a slightly

higher energy consumption.

Fig. 9 In the case of an appliance with enclosed wall spacers,

mount the wall spacers on the back of the appliance at the top

left and right.

u Dispose of packaging material. (see 4.5)

u Fig. 4

Align the appliance so that it stands firmly and on a

level by applying the accompanying spanner to the adjustable-

height feet (A) and using a spirit level. Then support the door:

Extend the adjustable foot at the turn hinge (B) until it rests on

the oor and then make a further 90° turn.

Note

u Clean the appliance (see 6.2).

If the appliance is installed in a very damp environment, conden-

sate may form on the outside of the appliance.

u Always see to good ventilation at the installation site.

4.3 Changing over the door hinges

You can change over the door hinges if necessary:

u see assembly instructions provided.

Ensure that the following tools are to hand:

q Torx® 25

q Screwdriver

q Cordless screwdriver, if necessary

q Second person for tting work, if needed

Note

u Remove any food from the door racks before removing the

door, so that no food falls out.

CAUTION

Risk of injury if the door tips!

u Take good hold of the door.

u Set down the door carefully.

WARNING

Risk of injury due to the door dropping out!

If the bearing parts are not screwed into place rmly enough,

the door may drop out. This may lead to severe injuries. What is

more, the door may not close and therefore the appliance may

fail to cool properly.

u Screw the turn hinges rmly into place with 4 Nm.

u Check all of the screws and retighten if necessary.

Liebherr CN 4213 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr CN 4213

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info