Bedienungsanleitung Liebherr CNd 5204 (Seite 23 von 26) (Englisch)

804805

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Defect Cause Remedy

The appliance

builds up too much

ice or condensa‐

tion.

→The door seal may have slipped out

of its groove.

uCheck that the door seal is well fitted in the groove.

The appliance is

hot to touch on the

outside*.

→The heat of the refrigeration circuit

is used to avoid condensation.

uThis is normal.

9.3.2 Features

Defect Cause Remedy

The internal light

does not come on.

→ The appliance is not switched on. uSwitch the appliance on.

→The door was open for longer than

15 minutes.

uInterior lighting turns off automatically after approx. 15

min. with the door open.

→The LED interior light is faulty or

the lid is damaged.

uContact customer service (see 9.4 Customer Services) .

9.4 Customer Services

First check if you can fix the error yourself (see 9 Customer

help) . If you can't, contact Customer Services.

Please refer to the enclosed “Liebherr-Service” brochure for

the address.

WARNING

Unprofessional repair!

Injuries.

uHave any repairs and action - not expressly specified -

on the appliance and mains cable carried out by service

personnel only. (see 8 Maintenance)

uA damaged mains cable may only be replaced by the

manufacturer, the manufacturer’s Customer Service or a

similarly qualified person.

uIn the case of appliances with an IEC connector, the

change may be made by the customer.

9.4.1 Contact Customer Services

Make sure you have the following appliance data at the

ready:

qAppliance name (model and index)

qService no. (Service)

qSerial no. (S no.)

uLook up the appliance information on the display

(see Info) .

-or-

uReferring to appliance info on the nameplate

(see 9.5 Model plate) .

uNote down the appliance information.

uNotify Customer Services of the following: Give us the

appliance data.

wThis will help us to provide you with a faster, more accu‐

rate service.

uFollow any further instructions given by Customer Serv‐

ices.

9.5 Model plate

The model plate is behind the drawers on the inside of the

appliance.

Fig. 51

(1) Appliance description (3) Serial no.

(2) Service no.

uNote the data on the model plate.

10 Shutting down

uEmpty the appliance.

uTurn off the appliance .

uRemove mains connector.

uRemove appliance connector if required: Remove and

move from left to right at the same time.

uClean the appliance (see 8.4 Cleaning the appliance) .

uLeave the door open to avoid bad smells building up.

11 Disposal

11.1 Preparing appliance for disposal

Liebherr uses batteries in some of its appli‐

ances. In the EU, for environmental reasons,

legislation obliges the end user to remove

these batteries before disposing of old appli‐

ances. If your appliance contains batteries, a

corresponding notice is attached.

Shutting down

* Depending on model and options 23

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr CNd 5204 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr CNd 5204

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info