Bedienungsanleitung Liebherr CNef 3115-20 (Seite 7 von 18) (Englisch)

710152

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

Detach the connecting cable from the rear of the appliance,

removing the cable holder at the same time because other-

wise there will be vibratory noise!

Remove the protective film from the outside of the appli-

ance.*

Remove the protective film from the decorative trims.

Remove all transit supports.

The spacers supplied with some appliances must be used to

achieve the stated energy consumption. These will extend the

depth of the appliance by approx. 35 mm. The appliance is fully

functional if the spacers are not used, but does have a slightly

higher energy consumption.

In the case of an appliance with

enclosed wall spacers, mount the

wall spacers on the back of the

appliance at the top left and right.

Dispose of packaging material (see 4.5) .

Align the appliance so that it

stands firmly and on a level by

applying the accompanying

spanner to the adjustable-

height feet (A) and using a

spirit level.

Then support the door:

Extend the adjustable foot at

the turn hinge (B) until it rests

on the floor and then make a

further 90° turn.

Note

Clean the appliance (see 6.2) .

If the appliance is installed in a very damp environment,

condensate may form on the outside of the appliance.

Always see to good ventilation at the installation site.

4.3 Changing over the door hinges

You can change over the door hinges if necessary.

Ensure that the following tools are to hand:

Torx® 25

Torx® 15

Screwdriver

Cordless screwdriver, if necessary

Second person for fitting work, if needed

4.3.1 Detaching the upper door

Note

Remove any food from the door racks before removing the

door, so that no food falls out.

Fig. 7

Close the upper door.

Pull off the cover

Fig. 7 (1)

forwards and upwards.

Lift off the cover

Fig. 7 (2)

CAUTION

Risk of injury if the door tips!

Take good hold of the door.

Set down the door carefully.

Unscrew the upper turn hinge

Fig. 7 (3)

(2x Torx® 25)

Fig. 7 (4)

and lift it off.

Lift up the upper door and set it aside.

4.3.2 Detaching the lower door

Close the lower door.

Draw the middle bearing pin

Fig. 8 (11)

out of the turn hinge

and lower door.

Remove the plastic cap

Fig. 8 (10)

CAUTION

Risk of injury if the door tips!

Take good hold of the door.

Set down the door carefully.

Open the lower door.

Unscrew the middle turn hinge (2x Torx® 25).

Fig. 8 (13)

Lift up the door and set it aside.

4.3.3 Transferring the middle bearing elements

Fig. 8

Carefully detach the cover panel

Fig. 8 (12)

Turn the middle turn hinge

Fig. 8 (13)

with the washer

Fig. 8 (14)

through 180° and screw it firmly into place on the

new hinge side (with 4 Nm).

Turn the cover panel

Fig. 8 (12)

through 180° and snap it into

place again on the new handle side.

Putting into operation

* Depending on model and options 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr CNef 3115-20 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr CNef 3115-20

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info