Bedienungsanleitung Liebherr CNef 4335-20 (Seite 7 von 28) (Englisch)

710158

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

4.2 Installing the appliance

WARNING

Fire hazard due to dampness!

If live parts or the mains lead become damp this may cause

short circuits.

uThe appliance is designed for use in enclosed areas. Do not

operate the appliance outdoors or in areas where it is

exposed to splash water or damp conditions.

WARNING

Risk of fire due to short circuit!

If the mains cable/connector of the appliance or of another

appliance touch the rear of the appliance, the mains cable/

connector may be damaged by the appliance vibrations,

leading to a short circuit.

uStand the appliance so that it is not touched by connectors

or main cables.

uDo not plug the appliance or any others into sockets located

near the rear of the appliance.

WARNING

Fire hazard due to refrigerant!

The coolant used is eco-friendly but also flammable. Any

leaking coolant may ignite.

uDo not damage the piping of the refrigeration circuit.

WARNING

Fire hazard and danger of damage!

uDo not place appliances emitting heat e.g. microwaves,

toasters etc. on the appliance!

WARNING

Blocked ventilation openings pose a risk of fire and damage!

uAlways keep the ventilation openings clear. Always ensure

that the appliance is properly ventilated!

NOTICE

Risk of damage due to condensate!

uDo not install the appliance directly alongside a further

refrigerator/freezer.

Note

If you have several appliances next to one another, leave a gap

of 70mm between appliances. Otherwise condensation will

build up between the units.

Fig. 8

qBefore you connect the appliance, report any damage

immediately to the delivery company.

qThe floor of the installation site must be horizontal and even.

qDo not install the appliance in direct sunlight, next to an

oven, radiator or similar.

qInstall the appliance with the rear panel up against the wall

and always use the supplied wall spacers (see below).

qOnly ever move the appliance when it is empty.

qThe surface supporting the appliance must be at the same

level as the surrounding floor.

qDo not install the appliance on your own.

qThe more coolant there is in the appliance, the larger the

room in which the appliance is installed must be. If the room

is too small, any leak may create a flammable mixture of gas

and air. For each 8 g of coolant the installation space must

be at least 1 m3. Information on the coolant is on the model

plate inside the appliance.

uRemove the protective film from the outside of the appli-

ance.*

NOTICE

Risk of damage from stainless steel care products!

The stainless steel doors and stainless steel side panels

are treated with a premium surface finish.

Stainless steel care products attack these surfaces.

uOnly use a soft, clean cloth to wipe down finished door

and side panel surfaces and painted door and side

panel surfaces. To remove heavy dirt, use a little water or

neutral detergent. Alternatively, you can use a micro-fibre

cloth.

uRemove the protective film from the decorative trims.

uRemove all transit supports.

Spacers must be used to achieve the declared energy

consumption and to prevent condensation in the event of high

surrounding humidity. This increases the appliance depth by

about 15 mm. The appliance will work perfectly well without the

spacers but will have a slightly higher energy consumption.

uIf your appliance comes with wall

spacers, mount these on the

back of the appliance, bottom left

and right.

uDispose of packaging material (see 4.5 Disposing of pack-

aging) .

uAlign the appliance so that it

stands firmly and on a level by

applying the accompanying

spanner to the adjustable-

height feet (A) and using a

spirit level.

uThen support the door: Use saddle wrench SW10 to

unscrew the base on mounting block (B) until it makes

contact with the ground, then continue turning it for a further

90°.

Note

uClean the appliance (see 6.4 Cleaning the appliance) .

Putting into operation

* Depending on model and options 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr CNef 4335-20 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr CNef 4335-20

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info