Bedienungsanleitung Liebherr CNPef 4313-20 (Seite 5 von 10) (Deutsch)

710175

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

Putting into operation

* Depending on model and options

4.5 Disposing of packaging

WARNING

Danger of suocation due to packing material and plastic

lm!

u Do not allow children to play with packaging material.

The packaging is made of recyclable materials:

- corrugated board/cardboard

- expanded polystyrene parts

- polythene bags and sheets

- polypropylene straps

- nailed wooden frame with polyethylene panel*

u Take the packaging material to an ocial collecting point.

4.6 Connecting the appliance

NOTICE

Failure to connect properly

Damage to the electronics.

u Do not use a standalone inverter.

u Do not use an energy saving plug.

WARNING

Failure to connect properly Fire.

u Do not use an extension cable.

u Do not use distributor blocks.

The type of current (alternating current) and voltage at the

installation site have to conform with the data on the type plate

(see Appliance at a glance).

The socket must be properly earthed and fused. The tripping

current for the fuse must be between 10 A and 16 A.

The socket must be easily accessible so that the appliance can

be quickly disconnected from the supply in an emergency. It must

be outside the area of the rear of the appliance.

u Check the electrical connection.

u Plug in the power plug.

4.7 Switching on the appliance

Note

u To switch on the entire appliance it is necessary only to switch

on the freezer compartment. In so doing, the refrigerator

compartment is automatically switched on as well.

The appliance should have been operating for about 2 hours

before you stock it with frozen food. Only place frozen goods in

the freeze compartment once the temperature display shows at

least -18°C.

4.7.1 Switching on the freezer compartment

u Press On/O button for the freezer section Fig. 11 (9).

 The appliance is switched on. The temperature display shows

the set temperature. The temperature display for the freezer

section and the alarm symbol ash until the temperature is

cold enough.

4.7.2 Switching on the refrigerator compartment

Note

u When the refrigerator compartment is switched on, the freezer

compartment is automatically switched on as well.

If the efrigerator compartment was switched o (e.g. with an

extended absence due to holiday), this can be switched on again

separately.

Press On/O button for the fridge section Fig. 11 (1).

 The interior light comes on when the door is open.

 The temperature displays light up. Refrigerator compartment

and freezer compartment are switched on.

functional if the spacers are not used, but does have a slightly

higher energy consumption.

Fig. 9 In the case of an appliance with enclosed wall spacers,

mount the wall spacers on the back of the appliance at the top

left and right.

u Dispose of packaging material. (see 4.5)

u Fig. 4

Align the appliance so that it stands firmly and

on a level by applying the accompanying spanner to the

adjustableheight feet (A) and using a spirit level. Then support

the door: Extend the adjustable foot at the turn hinge (B) until

it rests on the oor and then make a further 90° turn.

Note

u Clean the appliance (see 6.2).

If the appliance is installed in a very damp environment,

condensate may form on the outside of the appliance.

u Always see to good ventilation at the installation site.

4.3 Changing over the door hinges

You can change over the door hinges if necessary:

u see assembly instructions provided.

Ensure that the following tools are to hand:

q Torx® 25

q Screwdriver

q Cordless screwdriver, if necessary

q Second person for tting work, if needed

Note

u Remove any food from the door racks before removing the

door, so that no food falls out.

CAUTION

Risk of injury if the door tips!

u Take good hold of the door.

u Set down the door carefully.

WARNING

Risk of injury due to the door dropping out!

If the bearing parts are not screwed into place rmly enough,

the door may drop out. This may lead to severe injuries. What is

more, the door may not close and therefore the appliance may

fail to cool properly.

u Screw the turn hinges rmly into place with 4 Nm.

u Check all of the screws and retighten if necessary.

4.4 Insertion into a row of kitchen units

The appliance can be built into kitchen units.

u see assembly instructions provided.

Ventilation requirements:

A [mm] B [mm] C [cm

] D [mm] E [mm]

655

75 min. 300 min. 50 min. 19

For appliances supplied with wall spacers, the measurement

increases by 35 mm (see 4.2).

The appliance may protrude further, depending on the depth of

the kitchen units and the use of wall spacer brackets.

NOTICE

Risk of damage to the appliance due to overheating with

insucient ventilation!

The compressor may be damaged with insucient ventilation.

u Ensure sucient ventilation.

u Observe the ventilation requirements.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr CNPef 4313-20 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr CNPef 4313-20

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info