Bedienungsanleitung Liebherr CU 2831-20 (Seite 7 von 12) (Englisch)

710230

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

4.3.6 Fitting the upper door

uSet the upper door down on the centre bearing block .

uInsert the upper turn hinge

Fig. 5 (3)

in the door on the new

hinge side.

uScrew in the upper bearing block tightly (with 4 Nm) (2 x

Torx® 25)

Fig. 5 (4)

. Use a cordless screwdriver if

necessary.

uFit the cover

Fig. 5 (1)

on the opposite side by sliding it rear-

wards and latching it into place.

uPress the cover

Fig. 5 (2)

on the opposite side down into

place until it latches.

uUnscrew the adjustable foot

Fig. 7 (22)

on the lower bearing

block

Fig. 7 (23)

until it reaches the floor.

WARNING

Risk of injury due to the door dropping out!

If the bearing parts are not screwed into place firmly enough,

the door may drop out. This may lead to severe injuries. What is

more, the door may not close and therefore the appliance may

fail to cool properly.

uScrew the turn hinges firmly into place with 4 Nm.

uCheck all of the screws and retighten if necessary.

4.4 Insertion into a row of kitchen units

Fig. 8

(1) Stack cabinet (3) Kitchen cabinet

(2) Appliance (4) Wall

x For appliances supplied with wall spacers, the measurement

increases by 35 mm (see 4.2 Installing the appliance) .

The appliance can be built into kitchen units. A top cupboard

Fig. 8 (2)

can be added above the appliance in order to bring

the appliance

Fig. 8 (1)

up to the height of the fitted kitchen

units.

When installing with kitchen units (max. depth 580 mm), the

appliance can be positioned directly next to the kitchen cabinet

Fig. 8 (3)

. The appliance will project by 34 mm x at the sides

and 50 mm x in the centre of the appliance in relation to the

kitchen cabinet front.

NOTICE

Danger of overheating due to insufficient air ventilation!

The compressor may be damaged if there is insufficient air

ventilation.

uTake care to ensure adequate air ventilation.

uObserve the ventilation requirements.

Ventilation requirements:

-At the back of the stack cabinet there has to be a ventilation

duct of at least 50 mm depth throughout the width of the

stack cabinet.

-The cross section of the ventilation gap below the ceiling

must be at least 300 cm2 .

-the larger the ventilation space, the more energy-saving the

appliance is in operation.

If the appliance is installed with the hinges next to a wall

Fig. 8 (4)

, the distance between appliance and wall has to be at

least 40 mm. This corresponds to the projection of the handle

when the door is open.

4.5 Disposing of packaging

WARNING

Danger of suffocation due to packing material and plastic film!

uDo not allow children to play with packing material.

The packaging is made of recyclable materials:

-corrugated board/cardboard

-expanded polystyrene parts

-polythene bags and sheets

-polypropylene straps

-nailed wooden frame with polyethylene panel*

uTake the packaging material to an official collecting point.

4.6 Connecting the appliance

NOTICE

Failure to connect properly

Damage to the electronics.

uDo not use a standalone inverter.

uDo not use an energy saving plug.

WARNING

Failure to connect properly

Fire hazard.

uDo not use an extension cable.

uDo not use distributor blocks.

The type of current (alternating current) and voltage at the

installation site have to conform with the data on the type plate

(see 1 Appliance at a glance) .

The socket must be properly earthed and fused. The tripping

current for the fuse must be between 10 A and 16 A.

The socket must be easily accessible so that the appliance can

be quickly disconnected from the supply in an emergency. It

must be outside the area of the rear of the appliance.

uCheck the electrical connection.

uPlug in the power plug.

Putting into operation

* Depending on model and options 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr CU 2831-20 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr CU 2831-20

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info