Bedienungsanleitung Liebherr CUb 2331 (Seite 6 von 12) (Englisch)

804837

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

uAlign the appliance so that it

stands firmly and on a level by

applying the accompanying

spanner to the adjustable-

height feet (A) and using a

spirit level.

uThen support the door:

Extend the adjustable foot at

the turn hinge (B) until it rests

on the floor and then make a

further 90° turn.

Note

uClean the appliance (see 6.2 Cleaning the appliance) .

If the appliance is installed in a very damp environment,

condensate may form on the outside of the appliance.

uAlways see to good ventilation at the installation site.

4.3 Changing over the door hinges

You can change over the door hinges if necessary.

Ensure that the following tools are to hand:

qTorx® 15

qTorx® 25

qScrewdriver

qCordless screwdriver, if necessary

qSecond person for fitting work, if needed

4.3.1 Detaching the upper door

Note

uRemove any food from the door racks before removing the

door, so that no food falls out.

Fig. 5

uPull off the cover

Fig. 5 (1)

forwards and upwards.

uLift off the cover

Fig. 5 (2)

CAUTION

Risk of injury if the door tips!

uTake good hold of the door.

uSet down the door carefully.

uUnscrew the upper turn hinge

Fig. 5 (3)

(2x Torx® 25)

Fig. 5 (4)

and lift it off.

uLift up the upper door and set it aside.

4.3.2 Detaching the lower door

uOpen the lower door.

CAUTION

Risk of injury if the door tips!

uTake good hold of the door.

uSet down the door carefully.

uUnscrew the fastening screws

Fig. 6 (11)

(2 x Torx® 25) and

pull the centre bearing block out of the lower door.

uRemove plastic washer

Fig. 6 (10)

uLift up the door and set it aside.

4.3.3 Transferring the middle bearing elements

Fig. 6

uRemove the cover

Fig. 6 (12)

carefully.

uRe-install the cover

Fig. 6 (12)

on the opposite side.

4.3.4 Transferring the lower bearing elements

Fig. 7

uUnscrew fastening screws

Fig. 7 (21)

uRemove the lower bearing block

Fig. 7 (23)

, complete with

bearing bolt

Fig. 7 (24)

, washer

Fig. 7 (26)

and adjustable

foot

Fig. 7 (22)

uUnscrew the bearing bolt

Fig. 7 (24)

, complete with washer

Fig. 7 (26)

, re-locate it into the mounting hole on the oppo-

site side of the bearing block and tighten again.

uCarefully remove the cover plate

Fig. 7 (25)

and re-locate it

to the other side.

uFasten the lower bearing block

Fig. 7 (23)

, complete with

bearing bolt

Fig. 7 (24)

, washer

Fig. 7 (26)

and adjustable

foot

Fig. 7 (22)

to the new hinge side, with the help of a cord-

less screwdriver if necessary, and tighten (with 4 Nm)

once again.

4.3.5 Fitting the lower door

uLower the bottom door onto the bearing bolt

Fig. 7 (24)

uClose the door.

uInsert the centre bearing block

Fig. 6 (13)

turned through

180° into the lower door and fasten firmly (with 4 Nm)to the

new hinge side with the fastening screws(2 x Torx® 25).

uRefit plastic washer

Fig. 6 (10)

Putting into operation

6 * Depending on model and options

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr CUb 2331 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr CUb 2331

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info