Bedienungsanleitung Liebherr FNc 7026 (Seite 13 von 26) (Englisch)

805534

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Fig. 20

uComplete the steps (see Fig. 74) .

wMaxIce is deactivated.

TubeClean*

This setting cleans the IceMaker pipes.*

Ensure that the following conditions are met:*

qIceMaker cleaning is ready (see 8.3.6 Cleaning the

IceMaker*) .

Activating the setting*

uActivate the setting in the Customer menu

(see 6.2 Control concept) .

wThe rinse process is ready (max. 60 min.): Symbol flashes.

wWater pipes are rinsed: Symbol flashes.

wRinsing process is complete: Function turns off automati‐

cally.

Display brightness

Set the brightness level of the display.

You can set the following brightness levels:

-40%

-60%

-80%

-100%

Choose the setting

uSet the level (see 6.2 Control concept) .

Door alarm

Set the time before the door alarm (see Close the door)

sounds.

The options are as follows:

-1 min

-2 min

-3 min

-Off

Choose the setting

uSet the time (see 6.4 Fault messages) .

Entry lock

This setting prevents unintentional use of the appliance,

e.g. by children.

Use:

-Avoid settings being changed unintentionally.

-Avoid the appliance being switched off unintentionally.

-Avoid the temperature being changed unintentionally.

Activating/deactivating settings

uActivating/deactivating. (see 6.2 Control

concept)

Info

This setting allows the appliance information to be read out

as well as access to the customer menu.

It provides the following information:

-Model name

-Index

-Serial number

-Service number

Show appliance data

uTap the navigation arrows Fig. 5 (1) repeatedly until the

settings appear.

uPress Confirm Fig. 5 (2).

uTap the navigation arrows Fig. 5 (1) repeatedly until the

information is displayed.

uRead the appliance info.

Reminder

Reminders are given out acoustically by a beep and visually

by a symbol in the display. The signal gets louder until the

alert stops.

Activating the setting

uActivating/deactivating (see 6.2 Control concept) .

Reset

This function resets all settings to the factory settings. All

settings that you have made thus far will be reset to their

original values.

Activating the setting

uActivate (see 6.2 Control concept) .

6.4 Fault messages

Fault messages appear in the display. There are two catego‐

ries of fault message:

Category Meaning

Message Reminder of general procedures. You can carry

out these procedures to eliminate the message.

Warning Appears when there are malfunctions. A signal

sounds in addition to the display. The signal

becomes louder until you acknowledge by

tapping the display. You can eliminate simple

defects yourself. For more serious defects, you

must contact customer service.

6.4.1 Warnings

Close the door

This message appears if the door is open for too long.

You can set how long it takes for this message to appear .

Controls

* Depending on model and options 13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr FNc 7026 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr FNc 7026

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info