Bedienungsanleitung Liebherr GG 55511 (Seite 8 von 20) (Deutsch, Englisch, Holländisch, Französisch)

597544

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Malfunctions

You may be able to rectify the following faults by checking

the possible causes yourself:

• Appliance does not function: the control lamps are not lit.

– Is the appliance switched on?

– Is the plug correctly fitted in the mains socket?

– Is the socket fuse intact?

• The temperature is not low enough:

– Is the temperature setting correct (see "Setting the temperature")?

– Does the separately installed thermometer show the correct read-

ing?

– Is the ventilation system working properly?

– Is the appliance set up too close to a heat source?

If none of the above causes

apply and you cannot rectify

the fault yourself, contact the

nearest customer service

department stating the type of

appliance

1, service number

2 and appliance number 3

as indicated on the type plate.

Shutting your appliance down

If your appliance is to be shut down for any length of time, switch it

o and disconnect the plug or remove the fuse. Clean the appliance

and leave the door open in order to prevent unpleasant smells.

The appliance complies with the relevant safety regulations and

EC directives 2004/108/EC and 2006/95/EC.

All types and models are subject to continuous improvement and

the manufacturer therefore reserves the right to make modica-

tions to the shape, equipment and technology.

Cleaning

Before cleaning always switch o the appliance. Pull out the

mains plug or remove/unscrew the fuse.

Clean the inside, equipment parts and outer walls with lukewarm

water and a little detergent. Do not use abrasive or acid cleaners

or chemical solvents.

Do not use steam cleaners because of the risk of injury and

damage.

• Ensure that no cleaning water penetrates into the elec trical com-

ponents.

• Dry all parts well with a cloth.

• Do not damage or remove the type plate on the inside of the ap-

pliance. It is very important for servicing purposes.

Safety lock

The lock is equipped with a safety

mechanism.

Locking the appliance:

• Insert the key as shown by arrow

• Turn the key 180°.

To unlock the appliance, the same

procedure must be repeated in the

same order.

Alarm messages

LED ashes, which reads HI

The interior is too warm.

This can be caused by:

• the freezer door being left open for a long time, allowing warm

ambient air to enter;

• a long power failure;

• a fault in the appliance.

In each case, make sure food has not defrosted or perished.

E0, EE or EL appears in the display, the appliance has a fault.

Consult the customer serv ice department indicating the fault

number displayed.

Defrosting

After the appliance has been in operation for some time, a layer

of frost or ice will form on the inside walls. This increases energy

consumption.

• Switch the appliance off to defrost. Pull out the mains plug.

• Wrap the frozen food in paper or blankets and store in a cool place.

• To speed up the defrosting process put a saucepan of hot water

on the compartment floor.

• Leave the door of the appliance open while defrosting. After

defrosting mop up the remaining water and clean the appliance.

Do not use any mechanical devices or other articial aids for defrosting

other than those recommended by the manufactur er.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr GG 55511 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info