Bedienungsanleitung Liebherr GNP 2313-21 (Seite 6 von 14) (Englisch)

710256

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

The more coolant there is in the appliance, the larger the

room in which the appliance is installed must be. If the room

is too small, any leak may create a flammable mixture of gas

and air. For each 8 g of coolant the installation space must

be at least 1 m

. Information on the coolant is on the model

plate inside the appliance.

Detach the connecting cable from the rear of the appliance,

removing the cable holder at the same time because other-

wise there will be vibratory noise!

Remove the protective film from the outside of the appli-

ance.*

NOTICE

Risk of damage from stainless steel care products!*

The stainless steel doors and stainless steel side walls are

finished with a high-quality surface coating.

Stainless steel care products will damage the surfaces.

Use only a soft, clean cloth to wipe the coated door

surfaces and side walls.

Remove all transit supports.

The spacers supplied with some appliances must be used to

achieve the stated energy consumption. These will extend the

depth of the appliance by approx. 35 mm. The appliance is fully

functional if the spacers are not used, but does have a slightly

higher energy consumption.

In the case of an appliance with

enclosed wall spacers, mount the

wall spacers on the back of the

appliance at the top left and right.

Dispose of packaging material (see 4.5 Disposing of pack-

aging) .

Align the appliance so that it

stands firmly and on a level by

applying the accompanying

spanner to the adjustable-

height feet (A) and using a

spirit level.

Note

Clean the appliance (see 6.2 Cleaning the appliance) .

If the appliance is installed in a very damp environment,

condensate may form on the outside of the appliance.

Always see to good ventilation at the installation site.

4.3 Changing over the door hinges

You can change over the door hinges if necessary.

Ensure that the following tools are to hand:

Torx 25

Torx 15

Screwdriver

Open-ended spanner included in supply package

Second person for fitting work, if needed

CAUTION

Risk of injury if the door tips!

Take good hold of the door.

Set down the door carefully.

Unscrew the securing screw on

the bottom right turn hinge.

Open the door.

Hold the door on the handle side

and at the bottom and lift it.

The bearing pin

Fig. 5 (21)

should

come out of the turn hinge

Fig. 6 (2)

If the bearing bolt

Fig. 5 (21)

doesn't undo press it out from

underneath.

Fig. 5

Swing door out at the bottom and remove it.

Fig. 6

Unscrew the turn hinge

Fig. 6 (2)

Unscrew the bearing element,

Fig. 6 (3)

transfer it to the

opposite location hole of the turn hinge and screw it firmly

into place.

Take the stopper

Fig. 6 (4)

out of the turn hinge and transfer

it to the receiving hole on the opposite side of the turn hinge.

Carefully lift off the cover

Fig. 6 (5)

on the handle side.

Undo the screw

Fig. 6 (6)

and transfer it to the opposite side.

Put the cover

Fig. 6 (5)

back on.

Screw the turn hinge

Fig. 6 (2)

firmly into place on the new

hinge side (with 4 Nm), possibly using a power screwdriver.

Fig. 7

Putting into operation

6 * Depending on model and options

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr GNP 2313-21 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr GNP 2313-21

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info