Bedienungsanleitung Liebherr GNP 2713-23 (Seite 7 von 14) (Englisch)

710260

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

Unscrew the turn hinge

Fig. 6 (2)

Unscrew the bearing element,

Fig. 6 (3)

transfer it to the

opposite location hole of the turn hinge and screw it firmly

into place.

Take the stopper

Fig. 6 (4)

out of the turn hinge and transfer

it to the receiving hole on the opposite side of the turn hinge.

Carefully lift off the cover

Fig. 6 (5)

on the handle side.

Undo the screw

Fig. 6 (6)

and transfer it to the opposite side.

Put the cover

Fig. 6 (5)

back on.

Screw the turn hinge

Fig. 6 (2)

firmly into place on the new

hinge side (with 4 Nm), possibly using a power screwdriver.

Fig. 7

At the top, use a screwdriver to unclip cover

Fig. 7 (7)

and

cover

Fig. 7 (8)

at the front, and remove by pulling out and

down.

Unscrew the bearing pin

Fig. 7 (9)

and screw it firmly into

place on the opposite side (with 4 Nm).

Refit the cover

Fig. 7 (7)

on the side of the bearing pin: insert

at the back, snap in at the front.

Fit the cover

Fig. 7 (8)

on the opposite side: insert at the

back, snap in at the front.

Fig. 8

Lift the stopper

Fig. 8 (12)

out of the door bearing bush and

transfer it.

Detach door handle, stoppers

Fig. 8 (10)

and pressure

plates

Fig. 8 (11)

and transfer to the opposite side.

When mounting the pressure plates, make sure they snap

into place properly.

Transfer the spring clamp

Fig. 9 (20)

: Depress the

latch nose and pull the

spring clamp off over it.

Slide the spring clamp into

place on the new hinge

side until it clicks into

place.

Fig. 9

Pull the bearing pin

Fig. 9 (21)

out of the door

bush and transfer it to the

opposite side together with

the washer. The latch nose

must point to the inner side

of the door, the notch to

the outer side.

Hang the door on the bearing pin

Fig. 7 (9)

at the top.

Swing the door in at the bottom and insert the bearing pin

Fig. 9 (21)

into the turn hinge. If necessary, turn the bearing

pin until it snaps into place.

Insert the securing screw

Fig. 5 (1)

at the bottom into the

bearing pin and tighten it (with 4 Nm).

If necessary, align the door flush with the appliance housing

using the two slots in the turn hinge. To do so, unscrew the

middle screw.

WARNING

Risk of injury due to the door dropping out!

If the bearing parts are not screwed into place firmly enough,

the door may drop out. This may lead to severe injuries. What is

more, the door may not close and therefore the appliance may

fail to cool properly.

Screw on the bearing brackets/bearing pins tightly (4 Nm).

Check all of the screws and retighten if necessary.

4.4 Insertion into a row of kitchen units

Fig. 10

(1) Stack cabinet (3) Kitchen cabinet

(2) Appliance (4) Wall

For appliances supplied with wall spacers, the measurement

increases by 35 mm (see 4.2 Installing the appliance) .

The appliance can be built into kitchen units. A top cupboard

Fig. 10 (2)

can be added above the appliance in order to bring

the appliance

Fig. 10 (1)

up to the height of the fitted kitchen

units.

Putting into operation

* Depending on model and options 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr GNP 2713-23 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr GNP 2713-23

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info