Bedienungsanleitung Liebherr GNP1066 (Seite 6 von 14) (Englisch)

805277

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

qDo not install the appliance on your own.

qThe more coolant there is in the appliance, the larger

the room in which the appliance is installed must be. If

the room is too small, any leak may create a flammable

mixture of gas and air. For each 8 g of coolant the instal‐

lation space must be at least 1 m3. Information on the

coolant is on the model plate inside the appliance.

uDetach the connecting cable from the rear of the appli‐

ance, removing the cable holder at the same time

because otherwise there will be vibratory noise!

uRemove all transit supports.

The spacers supplied with some appliances must be used to

achieve the stated energy consumption. These will extend

the depth of the appliance by approx. 35 mm. The appliance

is fully functional if the spacers are not used, but does have

a slightly higher energy consumption.

uIn the case of an appliance with

enclosed wall spacers, mount

the wall spacers on the back

of the appliance at the top left

and right.

uDispose of packaging material (see 4.5 Disposing of

packaging) .

uAlign the appliance so that it

stands firmly and on a level

by applying the accompa‐

nying spanner to the adjust‐

able-height feet (A) and

using a spirit level.

Note

uClean the appliance (see 6.2 Cleaning the appliance) .

If the appliance is installed in a very damp environment,

condensate may form on the outside of the appliance.

uAlways see to good ventilation at the installation site.

4.3 Changing over the door hinges

You can change over the door hinges if necessary.

Make sure that the following tools are at hand:

qTorx® 25

qTorx® 15

qSupplied open-ended wrench

qIf necessary, a second person to assist with installation

CAUTION

Risk of injury if the door tips!

uTake good hold of the door.

uSet down the door carefully.

Fig. 4 On appliances with a door handle

uFollow the sequence of the item numbers in the diagram.

WARNING

Risk of injury due to the door dropping out!

If the bearing parts are not screwed into place firmly

enough, the door may drop out. This may lead to severe

injuries. What is more, the door may not close and therefore

the appliance may fail to cool properly.

uScrew on the bearing brackets/bearing pins tightly (4

Nm).

uCheck all of the screws and retighten if necessary.

4.4 Sliding into the row of units

Fig. 5

(1) Top cupboard (3) Kitchen cabinet

(2) Appliance (4) Wall

x For appliances with supplied wall spacers, add 35 mm

(see 4.2 Installing the appliance) to the dimensions.

The appliance can be built into kitchen units. A top

cupboard Fig. 5 (2) can be added above the appliance in

order to bring the appliance Fig. 5 (1) up to the height of the

fitted kitchen units.

Putting into operation

6 * Depending on model and options

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr GNP1066 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr GNP1066

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info