Bedienungsanleitung Liebherr GP 2033-20 (Seite 6 von 14) (Englisch)

710287

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

Note

Clean the appliance (see 6.2 Cleaning the appliance) .

If the appliance is installed in a very damp environment,

condensate may form on the outside of the appliance.

Always see to good ventilation at the installation site.

4.3 Changing over the door hinges

You can change over the door hinges if necessary.

Ensure that the following tools are to hand:

Torx 25

Torx 15

Open-ended spanner size 10

Screwdriver

Open-ended spanner included in supply package

Second person for fitting work, if needed

CAUTION

Risk of injury if the door tips!

Take good hold of the door.

Set down the door carefully.

Unscrew the securing screw on

the bottom right turn hinge.

Open the door.

Hold the door on the handle side

and at the bottom and lift it.

The bearing pin

Fig. 5 (21)

should

come out of the turn hinge

Fig. 6 (2)

If the bearing bolt

Fig. 5 (21)

doesn't undo press it out from

underneath.

Fig. 5

Swing door out at the bottom and remove it.

Fig. 6

Unscrew the turn hinge

Fig. 6 (2)

Unscrew the bearing element,

Fig. 6 (3)

transfer it to the

opposite location hole of the turn hinge and screw it firmly

into place.

Take the stopper

Fig. 6 (4)

out of the turn hinge and transfer

it to the receiving hole on the opposite side of the turn hinge.

Carefully lift off the cover

Fig. 6 (5)

on the handle side.

Undo the screw

Fig. 6 (6)

and transfer it to the opposite side.

Put the cover

Fig. 6 (5)

back on.

Screw the turn hinge

Fig. 6 (2)

firmly into place on the new

hinge side (with 4 Nm), possibly using a power screwdriver.

Fig. 7

At the top, use a screwdriver to unclip cover

Fig. 7 (7)

and

cover

Fig. 7 (8)

at the front, and remove by pulling out and

down.

Unscrew the bearing pin

Fig. 7 (9)

and screw it firmly into

place on the opposite side (with 4 Nm).

Refit the cover

Fig. 7 (7)

on the side of the bearing pin: insert

at the back, snap in at the front.

Fit the cover

Fig. 7 (8)

on the opposite side: insert at the

back, snap in at the front.

Fig. 8

Lift the stopper

Fig. 8 (12)

out of the door bearing bush and

transfer it.

Detach door handle, stoppers

Fig. 8 (10)

and pressure

plates

Fig. 8 (11)

and transfer to the opposite side.

When mounting the pressure plates, make sure they snap

into place properly.

Transfer the spring clamp

Fig. 9 (20)

: Depress the

latch nose and pull the

spring clamp off over it.

Slide the spring clamp into

place on the new hinge

side until it clicks into

place.

Pull the bearing pin

Fig. 9 (21)

out of the door

bush and transfer it to the

opposite side together with

the washer. The latch nose

must point to the inner side

of the door, the notch to

the outer side.

Fig. 9

Hang the door on the bearing pin

Fig. 7 (9)

at the top.

Swing the door in at the bottom and insert the bearing pin

Fig. 9 (21)

into the turn hinge. If necessary, turn the bearing

pin until it snaps into place.

Insert the securing screw

Fig. 5 (1)

at the bottom into the

bearing pin and tighten it (with 4 Nm).

If necessary, align the door flush with the appliance housing

using the two slots in the turn hinge. To do so, unscrew the

middle screw.

Putting into operation

6 * Depending on model and options

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr GP 2033-20 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr GP 2033-20

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info