Bedienungsanleitung Liebherr GP1386 (Seite 6 von 14) (Englisch)

805280

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

NOTICE

Covered vents!

Damage. Appliance can overheat, which can reduce the

service life of various parts of the appliance and lead to

operational impairments.

uAlways make sure there is good ventilation.

uAlways keep vents or ventilation grids in the appliance

housing and in the kitchen furniture (fully integrated

appliance) unobstructed.

NOTICE

Risk of damage due to condensate!

uDo not install the appliance directly alongside a further

refrigerator/freezer.

qBefore you connect the appliance, report any damage

immediately to the delivery company.

qThe floor of the installation site must be horizontal and

even.

qDo not install the appliance in direct sunlight, next to an

oven, radiator or similar.

qThe best place for installation is a dry and well ventilated

room.

qInstall the appliance with the rear panel up against the

wall and always use the supplied wall spacers (see

below).

qOnly ever move the appliance when it is empty.

qThe surface supporting the appliance must be at the

same level as the surrounding floor.

qDo not install the appliance on your own.

qThe more refrigerant there is in the appliance, the larger

the space that it is installed in must be. If the space is

too small, any leak may create a flammable mixture of

gas and air. For every 8 g of refrigerant, the installation

space must be at least 1 m3. Information regarding the

coolant can be found on the type plate inside the appli‐

ance.

uDetach the connecting cable from the rear of the appli‐

ance, removing the cable holder at the same time

because otherwise there will be vibratory noise!

uRemove the protective film from the outside of the appli‐

ance.*

uRemove all transit supports.

To achieve the specified energy consumption, use the

spacers, which are supplied with some appliances. This

increases the appliance depth by approx. 35 mm. The

appliance will work properly without the spacers but will

consume slightly more energy.

uIn the case of an appliance with

enclosed wall spacers, mount

the wall spacers on the back

of the appliance at the top left

and right.

uDispose of packaging material (see 4.5 Disposing of

packaging) .

uAlign the appliance so that it

stands firmly and on a level

by applying the accompa‐

nying spanner to the adjust‐

able-height feet (A) and

using a spirit level.

Note

uClean the appliance (see 6.2 Cleaning the appliance) .

If the appliance is installed in a very damp environment,

condensate may form on the outside of the appliance.

uAlways see to good ventilation at the installation site.

4.3 Changing over the door hinges

You can change over the door hinges if necessary.

Make sure that the following tools are at hand:

qTorx® 20

qTorx® 15

qSupplied open-ended wrench

qIf necessary, a second person to assist with installation

CAUTION

Risk of injury if the door tips!

uTake good hold of the door.

uSet down the door carefully.

Fig. 4 On appliances with a door handle

uFollow the sequence of the item numbers in the diagram.

Putting into operation

6 * Depending on model and options

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr GP1386 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr GP1386

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info