Bedienungsanleitung Liebherr IRBAd 5190 (Seite 17 von 34) (Englisch)

805595

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

Language

This setting lets you choose the language of the display.

Choose from the following languages:

-German

-English

-French

-Spanish

-Italian

-Dutch

-Czech

-Polish

-Portuguese

-Russian

-Chinese

Activating/deactivating settings

uActivating/deactivating (see 6.2 Control concept) .

Info

This setting allows the appliance information to be read out

as well as access to the customer menu.

It provides the following information:

-Model name

-Index

-Serial number

-Service number

Show appliance data

uSwipe in the display until Settings appears.

uConfirm the display.

uSwipe in the display until About appears.

uRead the appliance info.

Reminder

Reminders are given out acoustically by a beep and visually

by a symbol in the display. The signal gets louder until the

alert stops.

Replace water filter*

This message appears when the water filter needs

replacing.

uReplace the water filter every 6 months.

uConfirm the message with OK.

wThe service interval resets.

wThe water filter guarantees the best water quality.

Replace FreshAir active carbon filter

This message appears when the air filter needs replacing.

uChange the air filter every six months.

uConfirm the message with OK.

wThe service interval resets.

wThe air filter guarantees the air quality in the fridge.

Activating the setting

uActivating/deactivating (see 6.2 Control concept) .

Reset

This function resets all settings to the factory settings. All

settings that you have made thus far will be reset to their

original values.

Activating the setting

uActivate (see 6.2 Control concept) .

6.4 Fault messages

Fault messages appear in the display. There are two catego‐

ries of fault message:

Category Meaning

Message Reminder of general procedures. You can carry

out these procedures to eliminate the message.

Warning Appears when there are malfunctions. A signal

sounds in addition to the display. The signal

becomes louder until you acknowledge by

tapping the display. You can eliminate simple

defects yourself. For more serious defects, you

must contact customer service.

6.4.1 Warnings

Close the door

This message appears if the door is open for too long.

You can set how long it takes for this message to appear .

uStop alarm: Confirm the message.

-or-

uClose the door.

Error

This message appears if there is a fault with the appliance.

An appliance component indicates a fault.

uOpen the door.

uNote down the fault code.

uConfirm the message.

wThe signal tone stops.

wThe status display appears.

uClose the door.

uContact customer service. (see 9.4 Customer Services)

AutoDoor

The AutoDoor warning appears in the display:

Fig. 23

(1) Warning in the display

Warning in the display Remedy

AutoDoor has been stopped. Remove obstacle.

Position could not be saved. The door opening angle

must be more than 70°.

(see Changing the door

opening angle)

Controls

* Depending on model and options 17

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr IRBAd 5190 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr IRBAd 5190

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info