Bedienungsanleitung Liebherr SBSes 8483 (Seite 12 von 24) (Englisch)

719386

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Remove the locking device.

Fig. 21 (3)

Slide on the cover.

Fig. 21 (4)

Fig. 22

Position the bearing bracket and engage. If necessary push

apart carefully.

Fig. 22 (1)

Position the panel.

Fig. 22 (2)

Swing in the panel and click into place.

Fig. 22 (3)

Slide on the external cover.

Fig. 22 (4)

Close the upper door.

Fig. 22 (5)

4.4 Insertion into a row of kitchen units

Fig. 23

A [mm] B [mm]

C [cm

]

D [mm] E [mm]

665

65 Min. 300 Min. 50 Min. 46

If wall spacers are used, the dimensions increase by 15 mm

(see 4.2 Installing the appliance) .

The dimensions apply for an opening angle of 90 °. Spacing

angles will vary according to the opening angle.

You can purchase a kit to limit the door opening angle to 90° on

soft closing appliances. Please contact our customer service

team.

The appliance can be built into kitchen units. A top cupboard

Fig. 23 (2)

can be added above the appliance in order to bring

the appliance

Fig. 23 (1)

up to the height of the fitted kitchen

units.

The appliance can be installed right next to the kitchen cabinet

Fig. 23 (3)

. The appliance must stick out by the depth

Fig. 23 (B)

from the front of the cabinet so that the doors can be

opened fully. The appliance may protrude further depending on

the depth of the kitchen cabinets and whether wall spacers are

used.

NOTICE

Danger of overheating due to insufficient air ventilation!

The compressor may be damaged if there is insufficient air

ventilation.

Take care to ensure adequate air ventilation.

Observe the ventilation requirements.

Ventilation requirements:

Spacer ribs on the back of the appliance provide sufficient

air ventilation. In the final appliance position, these must not

be placed in recesses or cut-outs.

There must be a ventilation shaft with the depth

Fig. 23 (D)

at the back of the top cupboard over the entire width of the

cupboard.

The ventilation shaft

Fig. 23 (C)

must be observed under the

ceiling.

the larger the ventilation space, the more energy-saving the

appliance is in operation.

If the appliance is installed with the hinges next to a wall

Fig. 23 (4)

the distance

Fig. 23 (E)

between the appliance and

the wall must be observed. This is how far the handle protrudes

when the door is open.

4.5 Disposing of packaging

WARNING

Danger of suffocation due to packing material and plastic film!

Do not allow children to play with packing material.

The packaging is made of recyclable materials:

corrugated board/cardboard

expanded polystyrene parts

polythene bags and sheets

polypropylene straps

nailed wooden frame with polyethylene panel*

Take the packaging material to an official collecting point.

4.6 Connecting the appliance

WARNING

Failure to connect properly

Fire hazard.

Do not use an extension cable.

Do not use distributor blocks.

NOTICE

Failure to connect properly

Damage to the electronics.

Do not use a standalone inverter.

Do not use an energy saving plug.

Putting into operation

12 * Depending on model and options

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr SBSes 8483 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info