Bedienungsanleitung Liebherr SBSes 8496 (Seite 18 von 30) (Englisch)

715385

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

A [mm] B [mm]

C [cm

]

D [mm] E [mm]

665

65 Min. 300 Min. 50 Min. 46

If wall spacers are used, the dimensions increase by 15 mm

(see 4.2 Installing the appliance) .

The dimensions apply for an opening angle of 90 °. Spacing

angles will vary according to the opening angle.

You can purchase a kit to limit the door opening angle to 90° on

soft closing appliances. Please contact our customer service

team.

The appliance can be built into kitchen units. A top cupboard

Fig. 47 (2)

can be added above the appliance in order to bring

the appliance

Fig. 47 (1)

up to the height of the fitted kitchen

units.

The appliance can be installed right next to the kitchen cabinet

Fig. 47 (3)

. The appliance must stick out by the depth

Fig. 47 (B)

from the front of the cabinet so that the doors can be

opened fully. The appliance may protrude further depending on

the depth of the kitchen cabinets and whether wall spacers are

used.

NOTICE

Danger of overheating due to insufficient air ventilation!

The compressor may be damaged if there is insufficient air

ventilation.

Take care to ensure adequate air ventilation.

Observe the ventilation requirements.

Ventilation requirements:

Spacer ribs on the back of the appliance provide sufficient

air ventilation. In the final appliance position, these must not

be placed in recesses or cut-outs.

There must be a ventilation shaft with the depth

Fig. 47 (D)

at the back of the top cupboard over the entire width of the

cupboard.

The ventilation shaft

Fig. 47 (C)

must be observed under the

ceiling.

the larger the ventilation space, the more energy-saving the

appliance is in operation.

If the appliance is installed with the hinges next to a wall

Fig. 47 (4)

the distance

Fig. 47 (E)

between the appliance and

the wall must be observed. This is how far the handle protrudes

when the door is open.

4.6 Disposing of packaging

WARNING

Danger of suffocation due to packing material and plastic film!

Do not allow children to play with packing material.

The packaging is made of recyclable materials:

corrugated board/cardboard

expanded polystyrene parts

polythene bags and sheets

polypropylene straps

nailed wooden frame with polyethylene panel*

Take the packaging material to an official collecting point.

4.7 Connecting the appliance

WARNING

Failure to connect properly

Fire hazard.

Do not use an extension cable.

Do not use distributor blocks.

NOTICE

Failure to connect properly

Damage to the electronics.

Do not use a standalone inverter.

Do not use an energy saving plug.

Note

Only use the power connection lead supplied.

A longer power connection lead can be ordered from

Customer Service.

Fig. 48

a b c d G

~ 1800 mm ~ 1400 mm ~ 2100 mm ~ 200 mm Appliance

plugs

Ensure that the following conditions are met:

- The type of current and voltage at the installation site corre-

spond to the information on the model plate (see 1 Appli-

ance at a glance) .

- The socket is earthed according to the regulations and

fused.

- The fuse tripping current is between 10 and 16 A.

- The socket is easily accessible.

- The socket is outside the back of the appliance area in the

specified area

Fig. 48 (a, b, c)

Check the electrical connection.

Insert the appliance plug

Fig. 48 (G)

into the back of the

appliance. Ensure that it clicks into place.

Connect the power plug to the power supply.

The Liebherr logo appears on the screen.

The display switches to the standby symbol.

4.8 Switching on the appliance

Note

If the appliance is in demo mode, DEMO appears on the home-

screen.

Disable demo mode (see 7 Malfunctions) .

Note

The manufacturer recommends:

Store frozen produce at -18 °C or colder.

Connect and switch on appliance approx. 2 hours before

loading for the first time.

4.8.1 Switch on appliance

If the standby symbol is displayed over the whole screen:

Press the standby symbol.

The appliance is switched on. The display switches to the

home screen.

The appliance is set to the displayed temperatures. This is

shown by down arrows.

If the Standby symbol appears in the wine cooler or

freezer field:

Press the Standby symbol in the wine cooler or freezer field.

Putting into operation

18 * Depending on model and options

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr SBSes 8496 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr SBSes 8496

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info