Bedienungsanleitung Liebherr SBSes7273 (Seite 5 von 16) (Englisch)

57026

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

WARNING

Fire hazard due to refrigerant!

The refrigerant R 600a is environmentally friendly but flam-

mable. Escaping refrigerant may ignite.

uDo not damage the piping of the refrigeration circuit.

WARNING

Fire hazard and danger of damage!

uDo not place appliances emitting heat e.g. microwaves,

toasters etc. on the appliance!

WARNING

Blocked ventilation openings pose a risk of fire and damage!

uAlways keep the ventilation openings clear. Always ensure

that the appliance is properly ventilated!

qIn the event that the appliance is damaged, contact the

supplier immediately before connecting to the mains.

qThe floor at the site must be flat and level.

qDo not install the appliance in a location where it is exposed

to direct radiation of the sun, next to a cooker, heater and

similar.

qAlways stand the appliance backed directly to the wall using

the enclosed wall spacers (see below).

qThe appliance may be moved only when it is empty.

qDo not install the appliance without assistance.

qStandard EN 378 specifies that the room in which you install

your appliance must have a volume of 1 m2 per 8 g of R

600a refrigerant used in the appliance. If the room in which

the appliance is installed is too small, a flammable gas-air

mixture may form in the event of a leakage in the refrigera-

tion circuit. The quantity of refrigerant used in your appliance

is indicated on the type plate on the inside of the appliance.

uDetach the connecting cable from the rear of the appliance,

removing the cable holder at the same time because other-

wise there will be vibratory noise!

uRemove the protective film from the outside of the appli-

ance.

NOTICE

The stainless steel doors are provided with a high-quality

surface coating and must not be treated using the accompa-

nying care product.

Otherwise the surface coating will be affected.

uWipe the coated door surfaces using a soft, clean cloth

only.

uApply a stainless steel cleaner only to the stainless steel

side walls evenly, wiping with the grain. Subsequent

cleaning becomes easier as a result.

uWipe side walls with a paint finish using a soft, clean

cloth only.

uRemove all transit supports.

uDispose of packaging material (see 4.3) .

uMount the appliances according to the separate installation

instructions.

Note

uClean the appliance (see 6.3) .

If the appliance is installed in a very damp environment,

condensate may form on the outside of the appliance.

uAlways see to good ventilation at the installation site.

4.3 Disposing of packaging

WARNING

Danger of suffocation due to packing material and plastic film!

uDo not allow children to play with packing material.

The packaging is made of recyclable materials:

-corrugated board/cardboard

-expanded polystyrene parts

-polythene bags and sheets

-polypropylene straps

-nailed wooden frame with polyethylene panel*

uTake the packaging material to an official collecting point.

4.4 Connecting the appliance

NOTICE

Risk of damage to the electronic control system!

uDo not use stand-alone inverters (conversion of d.c. to a.c./

three-phase) or energy saving plugs.

WARNING

Fire and overheating hazard!

uDo not use extension cables or multiple socket outlets.

The type of current (alternating current) and voltage at the

installation site have to conform with the data on the type plate

(see Appliance at a glance).

Connect the appliance only with a properly installed

socket outlet with earthing contact. The socket outlet

must be fused with 10 A or higher.

It must be easily accessible so that the appliance can

be quickly disconnected from the supply in an emer-

gency. It must be outside the area of the rear of the

appliance.

Keep to the distance measurements to the socket outlet.

uCheck the electrical connection.

uPlug in the power plug.

4.5 Switching on the appliance

Note

uThe appliances can be switched on and off independently of

each other.

Put the appliance into operation about 2 hours before first

loading food to be frozen.

Do not load food to be frozen before the temperature display

reads -18 °C.

4.5.1 Switching on the freezer compartment

uPress On/Off button, freezer compartment

Fig. 2 (1)

wThe temperature display of the freezer compartment and the

alarm symbol flash until the temperature is sufficiently low. If

the temperature is above 0 °C, dashes flash. If it is below,

the current temperature flashes.

4.5.2 Switching on refrigerator and BioFresh

compartment

uPress On/Off button, refrigerator compartment

Fig. 2 (10)

wThe interior light is on when the door is open.

wThe temperature display shines. Refrigerator and BioFresh

compartment are switched on.

Putting into operation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr SBSes7273 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr SBSes7273

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info