Bedienungsanleitung Liebherr skes 3610 (Seite 24 von 26) (Englisch)

345020

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Setting the water intake time

The opening time of the IceMaker valve can be adjusted if, for

example, the water pressure in the line is too low or too high. The

water intake time is adjustable in steps from E1 (short intake time)

to E8 (long intake time).

To activate the setting mode: press the SuperFrost button

Fig. 3 (11)

for about 5 s.

The display indicates c.

Themenu symbol

Fig. 3 (15)

shines.

Using the Up setting button, freezer compartment

Fig. 3 (8)

and Down setting button, freezer compartment

Fig. 3 (9)

se-

lect E.

To confirm: briefly press the SuperFrost button

Fig. 3 (11)

To increase the water intake time:

press the Up setting button, freezer

compartment

Fig. 3 (8)

To reduce the water intake time: press

the Down setting button, freezer com-

partment

Fig. 3 (9)

To confirm: press the SuperFrost but-

ton

Fig. 3 (11)

To deactivate the setting mode: press the On/Off button,

freezer compartment

Fig. 3 (10)

-or-

Wait for 2 minutes.

6 Maintenance

6.1 Defrosting with NoFrost

The NoFrost system automatically defrosts the appliance.

BioFresh compartment:

The defrost water evaporates due to the compressor heat. Drops

of water on the rear wall are perfectly normal.

Freezer compartment:

The moisture condenses on the evaporator, is periodically de-

frosted and evaporates.

The appliance does not have to be manually defrosted.

6.2 Cleaning the appliance.

Before cleaning:

CAUTION

Risk of injury and damage as a result of hot steam!

Hot steam may damage the surfaces and cause burns.

Do not use any steam cleaners!

NOTICE

Incorrect cleaning damages the appliance!

Do not use cleaning agents in concentrated form.

Do not use any scouring or abrasive sponges or steel wool.

Do not use any cleaning agents containing sand, chloride,

chemicals or acid.

Do not use chemical solvents.

Do not damage or remove the type plate on the inside of the

appliance. It is important for the customer service.

Do not pull off, bend or damage cables or other components.

Do not allow any cleaning water to enter the drain channel,

ventilation grille or electrical parts.

Empty the appliance.

Pull out the plug.

- Use soft cleaning cloths and a multi-purpose clean-

ing agent with neutral pH value.

- Only use food compatible cleaning and care agents

on the inside of the appliance.

Outside surfaces and interior:

Regularly clean ventilation grilles.

Dust deposits increase energy consumption.

Clean the plastic surfaces, outside and inside, by hand using

lukewarm water and a little washing-up liquid.

NOTICE

The stainless steel doors have a high-quality surface coating and

must not be cleaned with the accompanying care product.

Otherwise the surface coating will be affected.

Wipe the coated door surfaces using a soft, clean cloth only.

In case of stubborn dirt, use a little water or a neutral cleaning

agent. A microfibre cloth can be optionally used.

If the stainless steel side walls are dirty, clean them using

a commercially available stainless steel cleaning agent. Then

evenly apply the accompanying stainless steel care product,

making strokes in the direction of the grain.

Wipe side walls with a paint finish using a soft, clean cloth

only. In case of stubborn dirt, use a little water or a neutral

cleaning agent. A microfibre cloth can be optionally used.

Clean stainless steel surfaces with a standard stainless steel

cleaning agent. Darker areas at the beginning and quite an in-

tensive colour of the stainless steel surface are normal.

Do not apply cleaners to glass or plastic surfaces so as not to

scratch them.

To clean the drain opening: remove any

deposits with a fine instrument, e.g. a cot-

ton bud.

Items of equipment:

Clean items of equipment by hand with lukewarm water and

a little washing-up liquid.

For cleaning, remove the support rails for the half-sized glass

shelves.

After cleaning:

Wipe dry the appliance and items of equipment.

Connect the appliance and switch it on again.

Switch on SuperFrost (see 5.7.4) .

When the temperature is sufficiently cold:

Put the food back inside.

6.3 Cleaning the IceMaker

The drawer of the IceMaker has to be emptied and slid in.

To activate the setting mode: press the SuperFrost button

Fig. 3 (11)

for about 5 s.

The display indicates c.

The menu symbol

Fig. 3 (15)

shines.

Using the Up setting button, freezer compartment

Fig. 3 (8)

/ Down setting button, freezer compart-

ment

Fig. 3 (9)

select Ic.

To confirm: press the SuperFrost button

Fig. 3 (11)

The IceMaker moves into the cleaning position and switches

off.

To deactivate the setting mode: press the On/Off button,

freezer compartment

Fig. 3 (10)

-or-

Wait for 2 minutes.

The temperature is indicated again in the temperature display.

Remove the drawer.

Clean the ice cube tray and drawer with warm water. If nec-

essary, use mild washing-up liquid. Then rinse.

Slide in the drawer again.

Maintenance

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr skes 3610 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr skes 3610

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info