Bedienungsanleitung Liebherr TP 1764-22 (Seite 7 von 14) (Englisch)

710417

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

The cross section of the ventilation gap below the ceiling

must be at least 300 cm

the larger the ventilation space, the more energy-saving the

appliance is in operation.

If the appliance is installed with the hinges next to a wall

Fig. 8 (4)

, the distance between appliance and wall has to be at

least 40 mm. This corresponds to the projection of the handle

when the door is open.

4.5 Disposing of packaging

WARNING

Danger of suffocation due to packing material and plastic film!

Do not allow children to play with packing material.

The packaging is made of recyclable materials:

corrugated board/cardboard

expanded polystyrene parts

polythene bags and sheets

polypropylene straps

nailed wooden frame with polyethylene panel*

Take the packaging material to an official collecting point.

4.6 Connecting the appliance

NOTICE

Failure to connect properly

Damage to the electronics.

Do not use a standalone inverter.

Do not use an energy saving plug.

WARNING

Failure to connect properly

Fire hazard.

Do not use an extension cable.

Do not use distributor blocks.

The type of current (alternating current) and voltage at the

installation site have to conform with the data on the type plate

(see 1 Appliance at a glance) .

The socket must be properly earthed and fused. The tripping

current for the fuse must be between 10 A and 16 A.

The socket must be easily accessible so that the appliance can

be quickly disconnected from the supply in an emergency. It

must be outside the area of the rear of the appliance.

Check the electrical connection.

Plug in the power plug.

4.7 Switching on the appliance

Press On/Off button

Fig. 3 (1)

The appliance is switched on. The temperature display indi-

cates the set temperature.

If “DEMO” is displayed, demo mode is activated. Please

contact the after sales service.

5 Control

5.1 Brightness of the temperature

display

You can adjust the brightness of the temperature display to the

light conditions of the room in which the appliance is installed.

5.1.1 Setting the brightness

The brightness is adjustable between h 0 (minimum bright-

ness) and h 5 (maximum brightness).

Activate setting mode by pressing the SuperFrost* button

Fig. 3 (3)

/SuperCool* button

Fig. 3 (4)

for approx. 5 sec.

The Menu symbol is shown on the display,

Fig. 3 (5)

c flashes on the display.

Use the adjustment button,

Fig. 3 (2)

, to select h.

Briefly confirm with the SuperFrost* button

Fig. 3 (3)

/Super-

Cool* button

Fig. 3 (4)

The display shows the last set brightness value.

Use the adjustment button,

Fig. 3 (2)

, to set the desired

value from h 0 to h 5.

Briefly confirm the newly set brightness value with the

SuperFrost* button

Fig. 3 (3)

/ SuperCool* button

Fig. 3 (4)

h flashes on the display.

The brightness is set.

After making the change, deactivate setting mode: Press the

On/Off button

Fig. 3 (1)

once.

The temperature display shows the temperature again.

If setting mode is already activated but you would like to keep

the old brightness value setting:

Press the On/Off button

Fig. 3 (1)

twice to deactivate setting

mode.

The temperature display shows the temperature again.

5.2 Child proofing

The child-proofing function enables you to make

sure that the appliance is not inadvertently switched

off by playing children.

5.2.1 Setting the child lock

To switch on the function:

Activate setting mode: press SuperFrost* button

Fig. 3 (3)

SuperCool* button

Fig. 3 (4)

for approx. 5 seconds.*

The Menu symbol

Fig. 3 (5)

is shown on the display.

c flashes on the display.

Briefly confirm with the SuperFrost* button

Fig. 3 (3)

/Super-

Cool* button

Fig. 3 (4)

c1 appears in the display.

Briefly confirm with the SuperFrost* button

Fig. 3 (3)

/Super-

Cool* button

Fig. 3 (4)

The child lock symbol

Fig. 3 (7)

, lights up on the

display.

c flashes on the display.

The child lock function is switched on.

If setting mode is to be terminated:

Briefly press the On/Off button

Fig. 3 (1)

-or-

Wait for 5 minutes.

The temperature display shows the temperature again.

To switch off the function:

Activate setting mode: press the SuperFrost* button

Fig. 3 (3)

/SuperCool* button

Fig. 3 (4)

for

approx. 5 seconds.*

The Menu symbol

Fig. 3 (5)

is shown on the display.

c flashes on the display.

Briefly confirm with the SuperFrost* button

Fig. 3 (3)

/Super-

Cool* button

Fig. 3 (4)

c0 appears in the display.

Briefly confirm with the SuperFrost* button

Fig. 3 (3)

/Super-

Cool* button

Fig. 3 (4)

The child lock symbol

Fig. 3 (7)

goes out.

Control

* Depending on model and options 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liebherr TP 1764-22 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Liebherr TP 1764-22

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info