Bedienungsanleitung Life Fitness T5 (Seite 28 von 30) (Englisch)

605544

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

trackIng (centerIng) an exIStIng or new StrIDIng beLt

1. Locate the two access holes to the BELT TENSIONING BOLTS on each of the rear roller guards. These tensioning

bolts make it possible to adjust tracking and centering of the striding belt without removing the guards.

2. Stand on the sides of the treadmill and straddle the belt. Enter the MANUAL

Workout and set the belt speed to run at 4.0 mph (6.4 kph).

3. If the striding belt has moved to the right, turn the right tension bolt 1/4 turn

clockwise with the provided 6MM Hex Key Wrench, and then turn the left

tension bolt 1/4 turn counter-clockwise to start striding belt tracking back to

center of roller.

4. If the striding belt has moved to the left, turn the left tension bolt 1/4 turn

clockwise and then turn the right tension bolt 1/4 turn counter-clockwise to

tart striding belt tracking back to center of roller. Repeat adjustments until the striding belt appears centered. Allow the

machine to continue running for several minutes to observe if tracking remains stabilized.

Note: Do not exceed one full turn of the adjusting screws in either direction. If after one full turn the belt does not track

properly, contact Customer Support Services.

tenSIonIng an exIStIng StrIDIng beLt

Under normal usage, the treadmill striding belt may stretch slightly. If the belt starts to slip during use, take the steps listed

below to correct the tension.

1. Using the STOP key, stop the treadmill.

2. Turn the belt tensioning bolts clockwise a quarter-turn per side to tension the belt. Do not exceed one full turn (four

quarter-turns per side).

3. Set the treadmill at 2.0-mph (3.2 kph) and get on to make sure the belt no longer slips. Also, check the striding belt’s

tracking. If the striding belt drifts to the left or right see Tracking (Centering) an Existing or New Striding Belt.

Note: Do not overtighten the tensioning bolts while making belt adjustments. Overtightening of bolts may over stretch

and damage the striding belt or roller bearings. Do not exceed one full turn of either bolt in either direction.

7.4 uSIng anD teStIng tHe Safety Stop puLL corD

During operation of the treadmill, the lanyard on the Safety Stop Pull Cord should be attached to an item of the user’s

clothing. While the treadmill is on and the console display is active, remove the Safety Stop Pull Cord from the treadmill. A

message shall be displayed on the console similar to “EMERGENCY STOP - REPLACE KEY”. With the Safety Stop Pull

Cord removed no keys shall function on the treadmill.

Place the Safety Stop Pull Cord back in place. The treadmill will reset and will be ready for operation.

7.5 How to obtaIn proDuct ServIce

1. Please contact your dealer or Life Fitness Customer Support Services at 1-800-351-3737.

2. Verify the symptom and review the operating instructions and troubleshooting matrix.

3. Locate and document the serial number of the treadmill. The treadmill’s serial number is located on the front of the

treadmill near the power switch. Please also have proof of purchase information available.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Life Fitness T5 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Life Fitness T5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info