Bedienungsanleitung LifeGear Accord Two in One Elliptical Trainer 93476 (Seite 19 von 23) (Englisch)

549151

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

DIST (DISTANCE): Displays the accumulative distance traveled during workout. You may

also pre-set target distance in STOP mode before training. To set DISTANCE press the

MODE button until you see the DIST displays on the screen. Press the SET button to

change the distance. Press the RESET button to clear the target distance to zero. The

pre-set target distance range is from 0.00 to 9999 km. Once you pre-set target distance

and then start to exercise, distance starts counting down from pre-set target distance to 0.00.

When the pre-set target distance counts down to 0.00, distance will start to count up and

the computer will begin beeping to remind you.

CAL (CALORIES): Displays the total accumulated calories burned during workout. You

may also pre-set target calories in STOP mode before training. To set CALORIES press

the MODE button until you see the CAL displays on the screen. Press the SET button to

change the calories. Press the RESET button to clear the target calories to zero. The

pre-set target calories range is from 0.0 to 9999 calories. Once you pre-set target calories

and then start to exercise, calories start counting down from pre-set target calories to 0.0.

When the pre-set target calories count down to 0.0, calories will start to count up and the

computer will begin beeping to remind you. (This data is a rough guide for comparison of

different exercise sessions and should not be used in medical treatment).

ODO (ODOMETER): Displays the total accumulative distance traveled. The data values of

ODO can not be clear to zero by pressing and holding the MODE or RESET button for 3

seconds. If you take out the batteries from the computer, the ODO data values will clear to

zero.

(PULSE): Displays your current heart rate figures after you grip the handlebar sensors

with both your hands during exercise. To ensure the pulse readout is more precise, please

always hold on to the handlebar grip sensors with two hands instead of just with one hand

only when you try to test your heart rate figures. You may also pre-set target heart rate in

STOP mode before training. To set PULSE press the MODE button until you see the

displays on the screen. Press the SET button to pre-set target heart rate. Press the

RESET button to clear the target heart rate to zero. Once you pre-set target heart rate and

then start to exercise, please grip the handlebar sensors with both your hands during

exercise. If the heart rate detected greater than the target heart rate, the computer will

begin beeping to remind you.

HOW TO INSTALL THE BATTERIES:

1. Remove the battery cover on the back of the computer.

2. Place two size AAA batteries into the battery housing.

3. Insure batteries are correctly positioned and battery springs are in proper contact with

batteries.

4. Re-install the battery cover.

5. If the display is illegible or only partial segment appears, remove batteries and wait 15

seconds before reinstalling.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

LifeGear Accord Two in One Elliptical Trainer 93476 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info