Bedienungsanleitung LifeGear Formula II - Magnetic Recumbent Bike 26280 (Seite 15 von 21) (Englisch)

552457

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

SPEED: Display the current training speed.

DIST (DISTANCE): Displays the accumulative distance traveled during workout. When you

start to exercise, distance starts counting up from 0.0 to 999.9 km per 0.1km increment.

You may also pre-set target distance in STOP mode before training. To set DISTANCE

press the MODE button until you see the DIST begin blinking. Press the SET button

to change the distance, each time you press the SET button DISTANCE should change by

1.0 km. Press the RESET button to clear the target distance to zero. The pre-set target

distance range is from 0.0 to 999.0 km. Once you pre-set target distance and then start to

exercise, distance starts counting down from pre-set target distance to 0.0. When the

pre-set target distance counts down to 0.0, distance will start to count up immediately and

the computer will begin beeping to remind you.

CAL (CALORIES): Displays the total accumulated calories burned during workout. When

you start to exercise, calories start counting up from 0.0 to 999.9 calories. You may also

pre-set target calories in STOP mode before training. To set CALORIES press the MODE

button until you see the CAL begin blinking. Press the SET button to change the calories,

each time you press the SET button CALORIES change by 1.0 calorie. Press the RESET

button to clear the target calories to zero. The pre-set target calories range is from 0.0 to

999.0 calories. Once you pre-set target calories and then start to exercise, calories start

counting down from pre-set target calories to 0.0. When the pre-set target calories count

down to 0.0, calories will start to count up immediately and the computer will begin beeping

to remind you. (This data is a rough guide for comparison of different exercise sessions

and should not be used in medical treatment).

ODO (ODOMETER): Displays the total accumulative distance traveled. The data values of

ODO can not be clear to zero by pressing and holding the MODE or RESET button for 3

seconds. If you take out the batteries from the computer, the ODO data values will clear to

zero.

(PULSE): Displays your current heart rate figures after you grip the handlebar sensors

with both your hands during exercise. To ensure the pulse readout is more precise, please

always hold on to the handlebar grip sensors with two hands instead of just with one hand

only when you try to test your heart rate figures. You may also pre-set target heart rate in

STOP mode before training. To set PULSE press the MODE button until you see the

PULSE begin blinking. Press the SET button to pre-set target heart rate. Press the

RESET button to clear the target heart rate to zero. The pre-set heart rate range is from 40

to 240 beats per minute. Once you pre-set target heart rate and then start to exercise,

please grip the handlebar sensors with both your hands during exercise. If the heart rate

detected greater than the target heart rate, the computer will begin beeping to remind you.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

LifeGear Formula II - Magnetic Recumbent Bike 26280 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info