Bedienungsanleitung LifeGoods LG1177 (Seite 10 von 17) (Englisch, Holländisch, Französisch)

805908

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

18 19

Note

-The alarm will sound for 2 minutes if you do not deactivate it by pressing any button. In this case the

alarm will be repeated automatically after 24 hours.

-Rising alarm sound (crescendo, duration: 2 minutes) changes the volume 4 times whilst the alarm signal

is heard.

Switching off the alarm signal

Press any button except the “ ” button to stop the alarm signal. It is not necessary to reactivate the

alarm. The alarm will set itself automatically to the previously set time.

Snooze function

Touch the “ “ eld or press the “ ” button to activate the snooze function. The alarm signal

will sound again after approx. 5 minutes.

Lunar phases

The weather station has a display which automatically displays the current lunar phase

°C/°F temperature display

-The temperature is displayed either in °C or °F. Briey press the “ ” button to switch between the

individual modes.

Comfort display

-indoor comfort level is calculated according to the indoor temperature and humidity, a total of 5 levels.

Displaying temperature/humidity/barometric pressure and temperature/humidity trend

-The current indoor temperature/humidity/barometric pressure and the temperature/humidity trend

(indoors) are shown in the LCD display.

-After successfully connecting with the remote sensor, the weather station can display the remote tem-

perature/humidity and the temperature/humidity trend (remote)

-You may see the following displays:

The temperature/humidity is rising.

The temperature/humidity is remaining constant.

The temperature/humidity is falling.

New moon Waxing

half-moon Half-moon Waxing full

moon

Full

moon

Waning full

moon Half-moon Waning

half-moon

Comfortable Too cold or too hot

Remote sensor transmission

When the Weather Station successfully receives signals from the wireless sensor, the temperature and

humidity of the “REMOTE SENSOR” are displayed on the “REMOTE SENSOR” column of the weather

station. The weather station can connect with up to 3 channel wireless sensors, but you can only choose

one channel at a time.

Press the “ ” key to switch the display of different channels of remote temperature and humidity. When

the “ “ is displayed, the channel will automatically switch every 5 seconds to different channels.

If the weather station failed to receive transmission from a remote sensor (“- -”display on the LCD),

press and hold the “ ” button for 3 seconds to receive transmission manually. The remote temperature

will show an animation of the RF antenna symbol, the Base Station will re-receive the wireless signal of

the remote sensor.

Note

-When the wireless sensor sets different channels, the weather station “REMOTE SENSOR” also wants

to switch to the same channel. When there is no wireless sensor signal transmission on the channel, “--”

will be displayed in the channel of the weather station

-When the wireless remote sensor has no channel selection function, the sensor defaults to channel 1.

Maximum / Minimum Temperature/and Relative Humidity

To switch between indoor/remote maximum, minimum temperature and humidity data, press the

“MEM” button:

-Once to display the maximum temperature and humidity values.

-Twice to display the minimum temperature and humidity values

-Three times to return to the current temperature and humidity levels

To reset the maximum and minimum temperature and humidity, press and hold down the “MEM”

button for about 2 seconds. This will reset all minimum and maximum data recorded to the current

displayed values.

Note

-If the temperature reading is below the temperature range, tLL.L will be displayed. If the temperature

reading is above the temperature range, HH.H will be displayed.

Setting the Remote Temperature Alert

Press and hold down the “ ” button for 2 seconds until the “Temperature Alert” icon starts to ash

The icon of Upper limit of the Temperature alarm starts to ash. Use the “ ” and “ ” buttons to set

the required maximum temperature. Press “ ” to conrm your setting.

The icon of the Lower limit of the Temperature alarm starts to ash. Use the “ ” and “ ” buttons to set

the required minimum temperature. Press “ ” to conrm your setting and to end the setting procedure

Note:

-Before entering the setup, you must select the correct channel, different channels can set different

temperature alarm ranges.

Temperature and frost alert

Press “ ” to activate or deactivate the remote temperature alert. When the remote temperature alarm

is activated, the temperature alarm icon is displayed in the remote sensor bar.

When the remote channel temperature value exceeds the set temperature range, the alarm will be acti-

vated. The Weather Station alarm will sound 5 times continuously every minute, while the temperature

alarm “ “ ashes. If the temperature activates the alarm, the upper limit icon “ “ or the lower limit

icon “ “ also ashes.

When the temperature of REMOTE SENSOR is –1°C to + 3°C or +30°F to + 37°F, the frost alarm will be

activated, the symbol “ “ will ash.

LifeGoods LG1177 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info